| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ntb_hw_switchtec: Fix shift-out-of-bounds in switchtec_ntb_mw_set_trans
There is a kernel API ntb_mw_clear_trans() would pass 0 to both addr and
size. This would make xlate_pos negative.
[ 23.734156] switchtec switchtec0: MW 0: part 0 addr 0x0000000000000000 size 0x0000000000000000
[ 23.734158] ================================================================================
[ 23.734172] UBSAN: shift-out-of-bounds in drivers/ntb/hw/mscc/ntb_hw_switchtec.c:293:7
[ 23.734418] shift exponent -1 is negative
Ensuring xlate_pos is a positive or zero before BIT. |
| In the Linux kernel, the following vulnerability has been resolved:
atl1c: Work around the DMA RX overflow issue
This is based on alx driver commit 881d0327db37 ("net: alx: Work around
the DMA RX overflow issue").
The alx and atl1c drivers had RX overflow error which was why a custom
allocator was created to avoid certain addresses. The simpler workaround
then created for alx driver, but not for atl1c due to lack of tester.
Instead of using a custom allocator, check the allocated skb address and
use skb_reserve() to move away from problematic 0x...fc0 address.
Tested on AR8131 on Acer 4540. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath12k: fix possible out-of-bound read in ath12k_htt_pull_ppdu_stats()
len is extracted from HTT message and could be an unexpected value in
case errors happen, so add validation before using to avoid possible
out-of-bound read in the following message iteration and parsing.
The same issue also applies to ppdu_info->ppdu_stats.common.num_users,
so validate it before using too.
These are found during code review.
Compile test only. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/jfs: Add check for negative db_l2nbperpage
l2nbperpage is log2(number of blks per page), and the minimum legal
value should be 0, not negative.
In the case of l2nbperpage being negative, an error will occur
when subsequently used as shift exponent.
Syzbot reported this bug:
UBSAN: shift-out-of-bounds in fs/jfs/jfs_dmap.c:799:12
shift exponent -16777216 is negative |
| In the Linux kernel, the following vulnerability has been resolved:
swiotlb: fix out-of-bounds TLB allocations with CONFIG_SWIOTLB_DYNAMIC
Limit the free list length to the size of the IO TLB. Transient pool can be
smaller than IO_TLB_SEGSIZE, but the free list is initialized with the
assumption that the total number of slots is a multiple of IO_TLB_SEGSIZE.
As a result, swiotlb_area_find_slots() may allocate slots past the end of
a transient IO TLB buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: wilc1000: use vmm_table as array in wilc struct
Enabling KASAN and running some iperf tests raises some memory issues with
vmm_table:
BUG: KASAN: slab-out-of-bounds in wilc_wlan_handle_txq+0x6ac/0xdb4
Write of size 4 at addr c3a61540 by task wlan0-tx/95
KASAN detects that we are writing data beyond range allocated to vmm_table.
There is indeed a mismatch between the size passed to allocator in
wilc_wlan_init, and the range of possible indexes used later: allocation
size is missing a multiplication by sizeof(u32) |
| In the Linux kernel, the following vulnerability has been resolved:
i3c: mipi-i3c-hci: Fix out of bounds access in hci_dma_irq_handler
Do not loop over ring headers in hci_dma_irq_handler() that are not
allocated and enabled in hci_dma_init(). Otherwise out of bounds access
will occur from rings->headers[i] access when i >= number of allocated
ring headers. |
| In the Linux kernel, the following vulnerability has been resolved:
riscv: VMAP_STACK overflow detection thread-safe
commit 31da94c25aea ("riscv: add VMAP_STACK overflow detection") added
support for CONFIG_VMAP_STACK. If overflow is detected, CPU switches to
`shadow_stack` temporarily before switching finally to per-cpu
`overflow_stack`.
If two CPUs/harts are racing and end up in over flowing kernel stack, one
or both will end up corrupting each other state because `shadow_stack` is
not per-cpu. This patch optimizes per-cpu overflow stack switch by
directly picking per-cpu `overflow_stack` and gets rid of `shadow_stack`.
Following are the changes in this patch
- Defines an asm macro to obtain per-cpu symbols in destination
register.
- In entry.S, when overflow is detected, per-cpu overflow stack is
located using per-cpu asm macro. Computing per-cpu symbol requires
a temporary register. x31 is saved away into CSR_SCRATCH
(CSR_SCRATCH is anyways zero since we're in kernel).
Please see Links for additional relevant disccussion and alternative
solution.
Tested by `echo EXHAUST_STACK > /sys/kernel/debug/provoke-crash/DIRECT`
Kernel crash log below
Insufficient stack space to handle exception!/debug/provoke-crash/DIRECT
Task stack: [0xff20000010a98000..0xff20000010a9c000]
Overflow stack: [0xff600001f7d98370..0xff600001f7d99370]
CPU: 1 PID: 205 Comm: bash Not tainted 6.1.0-rc2-00001-g328a1f96f7b9 #34
Hardware name: riscv-virtio,qemu (DT)
epc : __memset+0x60/0xfc
ra : recursive_loop+0x48/0xc6 [lkdtm]
epc : ffffffff808de0e4 ra : ffffffff0163a752 sp : ff20000010a97e80
gp : ffffffff815c0330 tp : ff600000820ea280 t0 : ff20000010a97e88
t1 : 000000000000002e t2 : 3233206874706564 s0 : ff20000010a982b0
s1 : 0000000000000012 a0 : ff20000010a97e88 a1 : 0000000000000000
a2 : 0000000000000400 a3 : ff20000010a98288 a4 : 0000000000000000
a5 : 0000000000000000 a6 : fffffffffffe43f0 a7 : 00007fffffffffff
s2 : ff20000010a97e88 s3 : ffffffff01644680 s4 : ff20000010a9be90
s5 : ff600000842ba6c0 s6 : 00aaaaaac29e42b0 s7 : 00fffffff0aa3684
s8 : 00aaaaaac2978040 s9 : 0000000000000065 s10: 00ffffff8a7cad10
s11: 00ffffff8a76a4e0 t3 : ffffffff815dbaf4 t4 : ffffffff815dbaf4
t5 : ffffffff815dbab8 t6 : ff20000010a9bb48
status: 0000000200000120 badaddr: ff20000010a97e88 cause: 000000000000000f
Kernel panic - not syncing: Kernel stack overflow
CPU: 1 PID: 205 Comm: bash Not tainted 6.1.0-rc2-00001-g328a1f96f7b9 #34
Hardware name: riscv-virtio,qemu (DT)
Call Trace:
[<ffffffff80006754>] dump_backtrace+0x30/0x38
[<ffffffff808de798>] show_stack+0x40/0x4c
[<ffffffff808ea2a8>] dump_stack_lvl+0x44/0x5c
[<ffffffff808ea2d8>] dump_stack+0x18/0x20
[<ffffffff808dec06>] panic+0x126/0x2fe
[<ffffffff800065ea>] walk_stackframe+0x0/0xf0
[<ffffffff0163a752>] recursive_loop+0x48/0xc6 [lkdtm]
SMP: stopping secondary CPUs
---[ end Kernel panic - not syncing: Kernel stack overflow ]--- |
| In the Linux kernel, the following vulnerability has been resolved:
powerpc/lib: Validate size for vector operations
Some of the fp/vmx code in sstep.c assume a certain maximum size for the
instructions being emulated. The size of those operations however is
determined separately in analyse_instr().
Add a check to validate the assumption on the maximum size of the
operations, so as to prevent any unintended kernel stack corruption. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix out of bounds read in smb2_sess_setup
ksmbd does not consider the case of that smb2 session setup is
in compound request. If this is the second payload of the compound,
OOB read issue occurs while processing the first payload in
the smb2_sess_setup(). |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix out-of-bound read in smb2_write
ksmbd_smb2_check_message doesn't validate hdr->NextCommand. If
->NextCommand is bigger than Offset + Length of smb2 write, It will
allow oversized smb2 write length. It will cause OOB read in smb2_write. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt76x0: fix oob access in mt76x0_phy_get_target_power
After 'commit ba45841ca5eb ("wifi: mt76: mt76x02: simplify struct
mt76x02_rate_power")', mt76x02 relies on ht[0-7] rate_power data for
vht mcs{0,7}, while it uses vth[0-1] rate_power for vht mcs {8,9}.
Fix a possible out-of-bound access in mt76x0_phy_get_target_power routine. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/ntfs3: Validate buffer length while parsing index
indx_read is called when we have some NTFS directory operations that
need more information from the index buffers. This adds a sanity check
to make sure the returned index buffer length is legit, or we may have
some out-of-bound memory accesses.
[ 560.897595] BUG: KASAN: slab-out-of-bounds in hdr_find_e.isra.0+0x10c/0x320
[ 560.898321] Read of size 2 at addr ffff888009497238 by task exp/245
[ 560.898760]
[ 560.899129] CPU: 0 PID: 245 Comm: exp Not tainted 6.0.0-rc6 #37
[ 560.899505] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014
[ 560.900170] Call Trace:
[ 560.900407] <TASK>
[ 560.900732] dump_stack_lvl+0x49/0x63
[ 560.901108] print_report.cold+0xf5/0x689
[ 560.901395] ? hdr_find_e.isra.0+0x10c/0x320
[ 560.901716] kasan_report+0xa7/0x130
[ 560.901950] ? hdr_find_e.isra.0+0x10c/0x320
[ 560.902208] __asan_load2+0x68/0x90
[ 560.902427] hdr_find_e.isra.0+0x10c/0x320
[ 560.902846] ? cmp_uints+0xe0/0xe0
[ 560.903363] ? cmp_sdh+0x90/0x90
[ 560.903883] ? ntfs_bread_run+0x190/0x190
[ 560.904196] ? rwsem_down_read_slowpath+0x750/0x750
[ 560.904969] ? ntfs_fix_post_read+0xe0/0x130
[ 560.905259] ? __kasan_check_write+0x14/0x20
[ 560.905599] ? up_read+0x1a/0x90
[ 560.905853] ? indx_read+0x22c/0x380
[ 560.906096] indx_find+0x2ef/0x470
[ 560.906352] ? indx_find_buffer+0x2d0/0x2d0
[ 560.906692] ? __kasan_kmalloc+0x88/0xb0
[ 560.906977] dir_search_u+0x196/0x2f0
[ 560.907220] ? ntfs_nls_to_utf16+0x450/0x450
[ 560.907464] ? __kasan_check_write+0x14/0x20
[ 560.907747] ? mutex_lock+0x8f/0xe0
[ 560.907970] ? __mutex_lock_slowpath+0x20/0x20
[ 560.908214] ? kmem_cache_alloc+0x143/0x4b0
[ 560.908459] ntfs_lookup+0xe0/0x100
[ 560.908788] __lookup_slow+0x116/0x220
[ 560.909050] ? lookup_fast+0x1b0/0x1b0
[ 560.909309] ? lookup_fast+0x13f/0x1b0
[ 560.909601] walk_component+0x187/0x230
[ 560.909944] link_path_walk.part.0+0x3f0/0x660
[ 560.910285] ? handle_lookup_down+0x90/0x90
[ 560.910618] ? path_init+0x642/0x6e0
[ 560.911084] ? percpu_counter_add_batch+0x6e/0xf0
[ 560.912559] ? __alloc_file+0x114/0x170
[ 560.913008] path_openat+0x19c/0x1d10
[ 560.913419] ? getname_flags+0x73/0x2b0
[ 560.913815] ? kasan_save_stack+0x3a/0x50
[ 560.914125] ? kasan_save_stack+0x26/0x50
[ 560.914542] ? __kasan_slab_alloc+0x6d/0x90
[ 560.914924] ? kmem_cache_alloc+0x143/0x4b0
[ 560.915339] ? getname_flags+0x73/0x2b0
[ 560.915647] ? getname+0x12/0x20
[ 560.916114] ? __x64_sys_open+0x4c/0x60
[ 560.916460] ? path_lookupat.isra.0+0x230/0x230
[ 560.916867] ? __isolate_free_page+0x2e0/0x2e0
[ 560.917194] do_filp_open+0x15c/0x1f0
[ 560.917448] ? may_open_dev+0x60/0x60
[ 560.917696] ? expand_files+0xa4/0x3a0
[ 560.917923] ? __kasan_check_write+0x14/0x20
[ 560.918185] ? _raw_spin_lock+0x88/0xdb
[ 560.918409] ? _raw_spin_lock_irqsave+0x100/0x100
[ 560.918783] ? _find_next_bit+0x4a/0x130
[ 560.919026] ? _raw_spin_unlock+0x19/0x40
[ 560.919276] ? alloc_fd+0x14b/0x2d0
[ 560.919635] do_sys_openat2+0x32a/0x4b0
[ 560.920035] ? file_open_root+0x230/0x230
[ 560.920336] ? __rcu_read_unlock+0x5b/0x280
[ 560.920813] do_sys_open+0x99/0xf0
[ 560.921208] ? filp_open+0x60/0x60
[ 560.921482] ? exit_to_user_mode_prepare+0x49/0x180
[ 560.921867] __x64_sys_open+0x4c/0x60
[ 560.922128] do_syscall_64+0x3b/0x90
[ 560.922369] entry_SYSCALL_64_after_hwframe+0x63/0xcd
[ 560.923030] RIP: 0033:0x7f7dff2e4469
[ 560.923681] Code: 00 f3 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 088
[ 560.924451] RSP: 002b:00007ffd41a210b8 EFLAGS: 00000206 ORIG_RAX: 0000000000000002
[ 560.925168] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f7dff2e4469
[ 560.925655] RDX: 0000000000000000 RSI: 0000000000000002 RDI:
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
i2c: ismt: Fix an out-of-bounds bug in ismt_access()
When the driver does not check the data from the user, the variable
'data->block[0]' may be very large to cause an out-of-bounds bug.
The following log can reveal it:
[ 33.995542] i2c i2c-1: ioctl, cmd=0x720, arg=0x7ffcb3dc3a20
[ 33.995978] ismt_smbus 0000:00:05.0: I2C_SMBUS_BLOCK_DATA: WRITE
[ 33.996475] ==================================================================
[ 33.996995] BUG: KASAN: out-of-bounds in ismt_access.cold+0x374/0x214b
[ 33.997473] Read of size 18446744073709551615 at addr ffff88810efcfdb1 by task ismt_poc/485
[ 33.999450] Call Trace:
[ 34.001849] memcpy+0x20/0x60
[ 34.002077] ismt_access.cold+0x374/0x214b
[ 34.003382] __i2c_smbus_xfer+0x44f/0xfb0
[ 34.004007] i2c_smbus_xfer+0x10a/0x390
[ 34.004291] i2cdev_ioctl_smbus+0x2c8/0x710
[ 34.005196] i2cdev_ioctl+0x5ec/0x74c
Fix this bug by checking the size of 'data->block[0]' first. |
| In the Linux kernel, the following vulnerability has been resolved:
fs: jfs: fix shift-out-of-bounds in dbDiscardAG
This should be applied to most URSAN bugs found recently by syzbot,
by guarding the dbMount. As syzbot feeding rubbish into the bmap
descriptor. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: fix potential out of bound read in ext4_fc_replay_scan()
For scan loop must ensure that at least EXT4_FC_TAG_BASE_LEN space. If remain
space less than EXT4_FC_TAG_BASE_LEN which will lead to out of bound read
when mounting corrupt file system image.
ADD_RANGE/HEAD/TAIL is needed to add extra check when do journal scan, as this
three tags will read data during scan, tag length couldn't less than data length
which will read. |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Fix reading strings from synthetic events
The follow commands caused a crash:
# cd /sys/kernel/tracing
# echo 's:open char file[]' > dynamic_events
# echo 'hist:keys=common_pid:file=filename:onchange($file).trace(open,$file)' > events/syscalls/sys_enter_openat/trigger'
# echo 1 > events/synthetic/open/enable
BOOM!
The problem is that the synthetic event field "char file[]" will read
the value given to it as a string without any memory checks to make sure
the address is valid. The above example will pass in the user space
address and the sythetic event code will happily call strlen() on it
and then strscpy() where either one will cause an oops when accessing
user space addresses.
Use the helper functions from trace_kprobe and trace_eprobe that can
read strings safely (and actually succeed when the address is from user
space and the memory is mapped in).
Now the above can show:
packagekitd-1721 [000] ...2. 104.597170: open: file=/usr/lib/rpm/fileattrs/cmake.attr
in:imjournal-978 [006] ...2. 104.599642: open: file=/var/lib/rsyslog/imjournal.state.tmp
packagekitd-1721 [000] ...2. 104.626308: open: file=/usr/lib/rpm/fileattrs/debuginfo.attr |
| In the Linux kernel, the following vulnerability has been resolved:
drm/fb-helper: Fix out-of-bounds access
Clip memory range to screen-buffer size to avoid out-of-bounds access
in fbdev deferred I/O's damage handling.
Fbdev's deferred I/O can only track pages. From the range of pages, the
damage handler computes the clipping rectangle for the display update.
If the fbdev screen buffer ends near the beginning of a page, that page
could contain more scanlines. The damage handler would then track these
non-existing scanlines as dirty and provoke an out-of-bounds access
during the screen update. Hence, clip the maximum memory range to the
size of the screen buffer.
While at it, rename the variables min/max to min_off/max_off in
drm_fb_helper_deferred_io(). This avoids confusion with the macros of
the same name. |
| In the Linux kernel, the following vulnerability has been resolved:
selinux: Add boundary check in put_entry()
Just like next_entry(), boundary check is necessary to prevent memory
out-of-bound access. |
| In the Linux kernel, the following vulnerability has been resolved:
media: imx-jpeg: Align upwards buffer size
The hardware can support any image size WxH,
with arbitrary W (image width) and H (image height) dimensions.
Align upwards buffer size for both encoder and decoder.
and leave the picture resolution unchanged.
For decoder, the risk of memory out of bounds can be avoided.
For both encoder and decoder, the driver will lift the limitation of
resolution alignment.
For example, the decoder can support jpeg whose resolution is 227x149
the encoder can support nv12 1080P, won't change it to 1920x1072. |
