| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net: ks8851: Reinstate disabling of BHs around IRQ handler
If the driver executes ks8851_irq() AND a TX packet has been sent, then
the driver enables TX queue via netif_wake_queue() which schedules TX
softirq to queue packets for this device.
If CONFIG_PREEMPT_RT=y is set AND a packet has also been received by
the MAC, then ks8851_rx_pkts() calls netdev_alloc_skb_ip_align() to
allocate SKBs for the received packets. If netdev_alloc_skb_ip_align()
is called with BH enabled, then local_bh_enable() at the end of
netdev_alloc_skb_ip_align() will trigger the pending softirq processing,
which may ultimately call the .xmit callback ks8851_start_xmit_par().
The ks8851_start_xmit_par() will try to lock struct ks8851_net_par
.lock spinlock, which is already locked by ks8851_irq() from which
ks8851_start_xmit_par() was called. This leads to a deadlock, which
is reported by the kernel, including a trace listed below.
If CONFIG_PREEMPT_RT is not set, then since commit 0913ec336a6c0
("net: ks8851: Fix deadlock with the SPI chip variant") the deadlock
can also be triggered without received packet in the RX FIFO. The
pending softirqs will be processed on return from
spin_unlock_bh(&ks->statelock) in ks8851_irq(), which triggers the
deadlock as well.
Fix the problem by disabling BH around critical sections, including the
IRQ handler, thus preventing the net_tx_action() softirq from triggering
during these critical sections. The net_tx_action() softirq is triggered
once BH are re-enabled and at the end of the IRQ handler, once all the
other IRQ handler actions have been completed.
__schedule from schedule_rtlock+0x1c/0x34
schedule_rtlock from rtlock_slowlock_locked+0x548/0x904
rtlock_slowlock_locked from rt_spin_lock+0x60/0x9c
rt_spin_lock from ks8851_start_xmit_par+0x74/0x1a8
ks8851_start_xmit_par from netdev_start_xmit+0x20/0x44
netdev_start_xmit from dev_hard_start_xmit+0xd0/0x188
dev_hard_start_xmit from sch_direct_xmit+0xb8/0x25c
sch_direct_xmit from __qdisc_run+0x1f8/0x4ec
__qdisc_run from qdisc_run+0x1c/0x28
qdisc_run from net_tx_action+0x1f0/0x268
net_tx_action from handle_softirqs+0x1a4/0x270
handle_softirqs from __local_bh_enable_ip+0xcc/0xe0
__local_bh_enable_ip from __alloc_skb+0xd8/0x128
__alloc_skb from __netdev_alloc_skb+0x3c/0x19c
__netdev_alloc_skb from ks8851_irq+0x388/0x4d4
ks8851_irq from irq_thread_fn+0x24/0x64
irq_thread_fn from irq_thread+0x178/0x28c
irq_thread from kthread+0x12c/0x138
kthread from ret_from_fork+0x14/0x28 |
| In the Linux kernel, the following vulnerability has been resolved:
tcp: call sk_data_ready() after listener migration
When inet_csk_listen_stop() migrates an established child socket from
a closing listener to another socket in the same SO_REUSEPORT group,
the target listener gets a new accept-queue entry via
inet_csk_reqsk_queue_add(), but that path never notifies the target
listener's waiters. A nonblocking accept() still works because it
checks the queue directly, but poll()/epoll_wait() waiters and
blocking accept() callers can also remain asleep indefinitely.
Call READ_ONCE(nsk->sk_data_ready)(nsk) after a successful migration
in inet_csk_listen_stop().
However, after inet_csk_reqsk_queue_add() succeeds, the ref acquired
in reuseport_migrate_sock() is effectively transferred to
nreq->rsk_listener. Another CPU can then dequeue nreq via accept()
or listener shutdown, hit reqsk_put(), and drop that listener ref.
Since listeners are SOCK_RCU_FREE, wrap the post-queue_add()
dereferences of nsk in rcu_read_lock()/rcu_read_unlock(), which also
covers the existing sock_net(nsk) access in that path.
The reqsk_timer_handler() path does not need the same changes for two
reasons: half-open requests become readable only after the final ACK,
where tcp_child_process() already wakes the listener; and once nreq is
visible via inet_ehash_insert(), the success path no longer touches
nsk directly. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: caiaq: Handle probe errors properly
The probe procedure of setup_card() in caiaq driver doesn't treat the
error cases gracefully, e.g. the error from snd_card_register() calls
snd_card_free() but continues. This would lead to a UAF for the
further calls like snd_usb_caiaq_control_init(), as Berk suggested in
another patch in the link below.
However, the problem is not only that; in general, this function drops
the all error handlings (as it's a void function) although its caller
can propagate an error to snd_probe(), which eventually calls
snd_card_free() as a proper error path. That said, we should treat
each error case in setup_card(), and just return the error code
promptly, which is then handled later as a fatal error in snd_probe().
This patch achieves it by changing the setup_card() to return an error
code. Also, the superfluous snd_card_free() call is removed, too.
Note that card->private_free can be set still safely at returning an
error. All called functions in card_free() have checks of the
unassigned resources or NULL checks. |
| In the Linux kernel, the following vulnerability has been resolved:
rtmutex: Use waiter::task instead of current in remove_waiter()
remove_waiter() is used by the slowlock paths, but it is also used for
proxy-lock rollback in rt_mutex_start_proxy_lock() when invoked from
futex_requeue().
In the latter case waiter::task is not current, but remove_waiter()
operates on current for the dequeue operation. That results in several
problems:
1) the rbtree dequeue happens without waiter::task::pi_lock being held
2) the waiter task's pi_blocked_on state is not cleared, which leaves a
dangling pointer primed for UAF around.
3) rt_mutex_adjust_prio_chain() operates on the wrong top priority waiter
task
Use waiter::task instead of current in all related operations in
remove_waiter() to cure those problems.
[ tglx: Fixup rt_mutex_adjust_prio_chain(), add a comment and amend the
changelog ] |
| In the Linux kernel, the following vulnerability has been resolved:
fbdev: udlfb: add vm_ops to dlfb_ops_mmap to prevent use-after-free
dlfb_ops_mmap() uses remap_pfn_range() to map vmalloc framebuffer pages
to userspace but sets no vm_ops on the VMA. This means the kernel cannot
track active mmaps. When dlfb_realloc_framebuffer() replaces the backing
buffer via FBIOPUT_VSCREENINFO, existing mmap PTEs are not invalidated.
On USB disconnect, dlfb_ops_destroy() calls vfree() on the old pages
while userspace PTEs still reference them, resulting in a use-after-free:
the process retains read/write access to freed kernel pages.
Add vm_operations_struct with open/close callbacks that maintain an
atomic mmap_count on struct dlfb_data. In dlfb_realloc_framebuffer(),
check mmap_count and return -EBUSY if the buffer is currently mapped,
preventing buffer replacement while userspace holds stale PTEs.
Tested with PoC using dummy_hcd + raw_gadget USB device emulation. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: roccat: fix use-after-free in roccat_report_event
roccat_report_event() iterates over the device->readers list without
holding the readers_lock. This allows a concurrent roccat_release() to
remove and free a reader while it's still being accessed, leading to a
use-after-free.
Protect the readers list traversal with the readers_lock mutex. |
| In the Linux kernel, the following vulnerability has been resolved:
ixgbevf: add missing negotiate_features op to Hyper-V ops table
Commit a7075f501bd3 ("ixgbevf: fix mailbox API compatibility by
negotiating supported features") added the .negotiate_features callback
to ixgbe_mac_operations and populated it in ixgbevf_mac_ops, but forgot
to add it to ixgbevf_hv_mac_ops. This leaves the function pointer NULL
on Hyper-V VMs.
During probe, ixgbevf_negotiate_api() calls ixgbevf_set_features(),
which unconditionally dereferences hw->mac.ops.negotiate_features().
On Hyper-V this results in a NULL pointer dereference:
BUG: kernel NULL pointer dereference, address: 0000000000000000
[...]
Hardware name: Microsoft Corporation Virtual Machine/Virtual Machine [...]
Workqueue: events work_for_cpu_fn
RIP: 0010:0x0
[...]
Call Trace:
ixgbevf_negotiate_api+0x66/0x160 [ixgbevf]
ixgbevf_sw_init+0xe4/0x1f0 [ixgbevf]
ixgbevf_probe+0x20f/0x4a0 [ixgbevf]
local_pci_probe+0x50/0xa0
work_for_cpu_fn+0x1a/0x30
[...]
Add ixgbevf_hv_negotiate_features_vf() that returns -EOPNOTSUPP and
wire it into ixgbevf_hv_mac_ops. The caller already handles -EOPNOTSUPP
gracefully. |
| In the Linux kernel, the following vulnerability has been resolved:
eventpoll: defer struct eventpoll free to RCU grace period
In certain situations, ep_free() in eventpoll.c will kfree the epi->ep
eventpoll struct while it still being used by another concurrent thread.
Defer the kfree() to an RCU callback to prevent UAF. |
| In the Linux kernel, the following vulnerability has been resolved:
dcache: Limit the minimal number of bucket to two
There is an OOB read problem on dentry_hashtable when user sets
'dhash_entries=1':
BUG: unable to handle page fault for address: ffff888b30b774b0
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
Oops: Oops: 0000 [#1] SMP PTI
RIP: 0010:__d_lookup+0x56/0x120
Call Trace:
d_lookup.cold+0x16/0x5d
lookup_dcache+0x27/0xf0
lookup_one_qstr_excl+0x2a/0x180
start_dirop+0x55/0xa0
simple_start_creating+0x8d/0xa0
debugfs_start_creating+0x8c/0x180
debugfs_create_dir+0x1d/0x1c0
pinctrl_init+0x6d/0x140
do_one_initcall+0x6d/0x3d0
kernel_init_freeable+0x39f/0x460
kernel_init+0x2a/0x260
There will be only one bucket in dentry_hashtable when dhash_entries is
set as one, and d_hash_shift is calculated as 32 by dcache_init(). Then,
following process will access more than one buckets(which memory region
is not allocated) in dentry_hashtable:
d_lookup
b = d_hash(hash)
dentry_hashtable + ((u32)hashlen >> d_hash_shift)
// The C standard defines the behavior of right shift amounts
// exceeding the bit width of the operand as undefined. The
// result of '(u32)hashlen >> d_hash_shift' becomes 'hashlen',
// so 'b' will point to an unallocated memory region.
hlist_bl_for_each_entry_rcu(b)
hlist_bl_first_rcu(head)
h->first // read OOB!
Fix it by limiting the minimal number of dentry_hashtable bucket to two,
so that 'd_hash_shift' won't exceeds the bit width of type u32. |
| In the Linux kernel, the following vulnerability has been resolved:
media: vidtv: fix pass-by-value structs causing MSAN warnings
vidtv_ts_null_write_into() and vidtv_ts_pcr_write_into() take their
argument structs by value, causing MSAN to report uninit-value warnings.
While only vidtv_ts_null_write_into() has triggered a report so far,
both functions share the same issue.
Fix by passing both structs by const pointer instead, avoiding the
stack copy of the struct along with its MSAN shadow and origin metadata.
The functions do not modify the structs, which is enforced by the const
qualifier. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix use-after-free of sbi in f2fs_compress_write_end_io()
In f2fs_compress_write_end_io(), dec_page_count(sbi, type) can bring
the F2FS_WB_CP_DATA counter to zero, unblocking
f2fs_wait_on_all_pages() in f2fs_put_super() on a concurrent unmount
CPU. The unmount path then proceeds to call
f2fs_destroy_page_array_cache(sbi), which destroys
sbi->page_array_slab via kmem_cache_destroy(), and eventually
kfree(sbi). Meanwhile, the bio completion callback is still executing:
when it reaches page_array_free(sbi, ...), it dereferences
sbi->page_array_slab — a destroyed slab cache — to call
kmem_cache_free(), causing a use-after-free.
This is the same class of bug as CVE-2026-23234 (which fixed the
equivalent race in f2fs_write_end_io() in data.c), but in the
compressed writeback completion path that was not covered by that fix.
Fix this by moving dec_page_count() to after page_array_free(), so
that all sbi accesses complete before the counter decrement that can
unblock unmount. For non-last folios (where atomic_dec_return on
cic->pending_pages is nonzero), dec_page_count is called immediately
before returning — page_array_free is not reached on this path, so
there is no post-decrement sbi access. For the last folio,
page_array_free runs while the F2FS_WB_CP_DATA counter is still
nonzero (this folio has not yet decremented it), keeping sbi alive,
and dec_page_count runs as the final operation. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: caiaq: take a reference on the USB device in create_card()
The caiaq driver stores a pointer to the parent USB device in
cdev->chip.dev but never takes a reference on it. The card's
private_free callback, snd_usb_caiaq_card_free(), can run
asynchronously via snd_card_free_when_closed() after the USB
device has already been disconnected and freed, so any access to
cdev->chip.dev in that path dereferences a freed usb_device.
On top of the refcounting issue, the current card_free implementation
calls usb_reset_device(cdev->chip.dev). A reset in a free callback
is inappropriate: the device is going away, the call takes the
device lock in a teardown context, and the reset races with the
disconnect path that the callback is already cleaning up after.
Take a reference on the USB device in create_card() with
usb_get_dev(), drop it with usb_put_dev() in the free callback,
and remove the usb_reset_device() call. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: hold claim backbone gateways by reference
batadv_bla_add_claim() can replace claim->backbone_gw and drop the old
gateway's last reference while readers still follow the pointer.
The netlink claim dump path dereferences claim->backbone_gw->orig and
takes claim->backbone_gw->crc_lock without pinning the underlying
backbone gateway. batadv_bla_check_claim() still has the same naked
pointer access pattern.
Reuse batadv_bla_claim_get_backbone_gw() in both readers so they operate
on a stable gateway reference until the read-side work is complete.
This keeps the dump and claim-check paths aligned with the lifetime
rules introduced for the other BLA claim readers. |
| In the Linux kernel, the following vulnerability has been resolved:
rxrpc: Fix call removal to use RCU safe deletion
Fix rxrpc call removal from the rxnet->calls list to use list_del_rcu()
rather than list_del_init() to prevent stuffing up reading
/proc/net/rxrpc/calls from potentially getting into an infinite loop.
This, however, means that list_empty() no longer works on an entry that's
been deleted from the list, making it harder to detect prior deletion. Fix
this by:
Firstly, make rxrpc_destroy_all_calls() only dump the first ten calls that
are unexpectedly still on the list. Limiting the number of steps means
there's no need to call cond_resched() or to remove calls from the list
here, thereby eliminating the need for rxrpc_put_call() to check for that.
rxrpc_put_call() can then be fixed to unconditionally delete the call from
the list as it is the only place that the deletion occurs. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: x86: Use scratch field in MMIO fragment to hold small write values
When exiting to userspace to service an emulated MMIO write, copy the
to-be-written value to a scratch field in the MMIO fragment if the size
of the data payload is 8 bytes or less, i.e. can fit in a single chunk,
instead of pointing the fragment directly at the source value.
This fixes a class of use-after-free bugs that occur when the emulator
initiates a write using an on-stack, local variable as the source, the
write splits a page boundary, *and* both pages are MMIO pages. Because
KVM's ABI only allows for physically contiguous MMIO requests, accesses
that split MMIO pages are separated into two fragments, and are sent to
userspace one at a time. When KVM attempts to complete userspace MMIO in
response to KVM_RUN after the first fragment, KVM will detect the second
fragment and generate a second userspace exit, and reference the on-stack
variable.
The issue is most visible if the second KVM_RUN is performed by a separate
task, in which case the stack of the initiating task can show up as truly
freed data.
==================================================================
BUG: KASAN: use-after-free in complete_emulated_mmio+0x305/0x420
Read of size 1 at addr ffff888009c378d1 by task syz-executor417/984
CPU: 1 PID: 984 Comm: syz-executor417 Not tainted 5.10.0-182.0.0.95.h2627.eulerosv2r13.x86_64 #3
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.15.0-0-g2dd4b9b3f840-prebuilt.qemu.org 04/01/2014 Call Trace:
dump_stack+0xbe/0xfd
print_address_description.constprop.0+0x19/0x170
__kasan_report.cold+0x6c/0x84
kasan_report+0x3a/0x50
check_memory_region+0xfd/0x1f0
memcpy+0x20/0x60
complete_emulated_mmio+0x305/0x420
kvm_arch_vcpu_ioctl_run+0x63f/0x6d0
kvm_vcpu_ioctl+0x413/0xb20
__se_sys_ioctl+0x111/0x160
do_syscall_64+0x30/0x40
entry_SYSCALL_64_after_hwframe+0x67/0xd1
RIP: 0033:0x42477d
Code: <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b0 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007faa8e6890e8 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 00000000004d7338 RCX: 000000000042477d
RDX: 0000000000000000 RSI: 000000000000ae80 RDI: 0000000000000005
RBP: 00000000004d7330 R08: 00007fff28d546df R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00000000004d733c
R13: 0000000000000000 R14: 000000000040a200 R15: 00007fff28d54720
The buggy address belongs to the page:
page:0000000029f6a428 refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x9c37
flags: 0xfffffc0000000(node=0|zone=1|lastcpupid=0x1fffff)
raw: 000fffffc0000000 0000000000000000 ffffea0000270dc8 0000000000000000
raw: 0000000000000000 0000000000000000 00000000ffffffff 0000000000000000 page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff888009c37780: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ffff888009c37800: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>ffff888009c37880: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
^
ffff888009c37900: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ffff888009c37980: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
==================================================================
The bug can also be reproduced with a targeted KVM-Unit-Test by hacking
KVM to fill a large on-stack variable in complete_emulated_mmio(), i.e. by
overwrite the data value with garbage.
Limit the use of the scratch fields to 8-byte or smaller accesses, and to
just writes, as larger accesses and reads are not affected thanks to
implementation details in the emulator, but add a sanity check to ensure
those details don't change in the future. Specifically, KVM never uses
on-stack variables for accesses larger that 8 bytes, e.g. uses an operand
in the emulator context, and *al
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: qcom: q6apm: move component registration to unmanaged version
q6apm component registers dais dynamically from ASoC toplology, which
are allocated using device managed version apis. Allocating both
component and dynamic dais using managed version could lead to incorrect
free ordering, dai will be freed while component still holding references
to it.
Fix this issue by moving component to unmanged version so
that the dai pointers are only freeded after the component is removed.
==================================================================
BUG: KASAN: slab-use-after-free in snd_soc_del_component_unlocked+0x3d4/0x400 [snd_soc_core]
Read of size 8 at addr ffff00084493a6e8 by task kworker/u48:0/3426
Tainted: [W]=WARN
Hardware name: LENOVO 21N2ZC5PUS/21N2ZC5PUS, BIOS N42ET57W (1.31 ) 08/08/2024
Workqueue: pdr_notifier_wq pdr_notifier_work [pdr_interface]
Call trace:
show_stack+0x28/0x7c (C)
dump_stack_lvl+0x60/0x80
print_report+0x160/0x4b4
kasan_report+0xac/0xfc
__asan_report_load8_noabort+0x20/0x34
snd_soc_del_component_unlocked+0x3d4/0x400 [snd_soc_core]
snd_soc_unregister_component_by_driver+0x50/0x88 [snd_soc_core]
devm_component_release+0x30/0x5c [snd_soc_core]
devres_release_all+0x13c/0x210
device_unbind_cleanup+0x20/0x190
device_release_driver_internal+0x350/0x468
device_release_driver+0x18/0x30
bus_remove_device+0x1a0/0x35c
device_del+0x314/0x7f0
device_unregister+0x20/0xbc
apr_remove_device+0x5c/0x7c [apr]
device_for_each_child+0xd8/0x160
apr_pd_status+0x7c/0xa8 [apr]
pdr_notifier_work+0x114/0x240 [pdr_interface]
process_one_work+0x500/0xb70
worker_thread+0x630/0xfb0
kthread+0x370/0x6c0
ret_from_fork+0x10/0x20
Allocated by task 77:
kasan_save_stack+0x40/0x68
kasan_save_track+0x20/0x40
kasan_save_alloc_info+0x44/0x58
__kasan_kmalloc+0xbc/0xdc
__kmalloc_node_track_caller_noprof+0x1f4/0x620
devm_kmalloc+0x7c/0x1c8
snd_soc_register_dai+0x50/0x4f0 [snd_soc_core]
soc_tplg_pcm_elems_load+0x55c/0x1eb8 [snd_soc_core]
snd_soc_tplg_component_load+0x4f8/0xb60 [snd_soc_core]
audioreach_tplg_init+0x124/0x1fc [snd_q6apm]
q6apm_audio_probe+0x10/0x1c [snd_q6apm]
snd_soc_component_probe+0x5c/0x118 [snd_soc_core]
soc_probe_component+0x44c/0xaf0 [snd_soc_core]
snd_soc_bind_card+0xad0/0x2370 [snd_soc_core]
snd_soc_register_card+0x3b0/0x4c0 [snd_soc_core]
devm_snd_soc_register_card+0x50/0xc8 [snd_soc_core]
x1e80100_platform_probe+0x208/0x368 [snd_soc_x1e80100]
platform_probe+0xc0/0x188
really_probe+0x188/0x804
__driver_probe_device+0x158/0x358
driver_probe_device+0x60/0x190
__device_attach_driver+0x16c/0x2a8
bus_for_each_drv+0x100/0x194
__device_attach+0x174/0x380
device_initial_probe+0x14/0x20
bus_probe_device+0x124/0x154
deferred_probe_work_func+0x140/0x220
process_one_work+0x500/0xb70
worker_thread+0x630/0xfb0
kthread+0x370/0x6c0
ret_from_fork+0x10/0x20
Freed by task 3426:
kasan_save_stack+0x40/0x68
kasan_save_track+0x20/0x40
__kasan_save_free_info+0x4c/0x80
__kasan_slab_free+0x78/0xa0
kfree+0x100/0x4a4
devres_release_all+0x144/0x210
device_unbind_cleanup+0x20/0x190
device_release_driver_internal+0x350/0x468
device_release_driver+0x18/0x30
bus_remove_device+0x1a0/0x35c
device_del+0x314/0x7f0
device_unregister+0x20/0xbc
apr_remove_device+0x5c/0x7c [apr]
device_for_each_child+0xd8/0x160
apr_pd_status+0x7c/0xa8 [apr]
pdr_notifier_work+0x114/0x240 [pdr_interface]
process_one_work+0x500/0xb70
worker_thread+0x630/0xfb0
kthread+0x370/0x6c0
ret_from_fork+0x10/0x20 |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: 6fire: fix use-after-free on disconnect
In usb6fire_chip_abort(), the chip struct is allocated as the card's
private data (via snd_card_new with sizeof(struct sfire_chip)). When
snd_card_free_when_closed() is called and no file handles are open, the
card and embedded chip are freed synchronously. The subsequent
chip->card = NULL write then hits freed slab memory.
Call trace:
usb6fire_chip_abort sound/usb/6fire/chip.c:59 [inline]
usb6fire_chip_disconnect+0x348/0x358 sound/usb/6fire/chip.c:182
usb_unbind_interface+0x1a8/0x88c drivers/usb/core/driver.c:458
...
hub_event+0x1a04/0x4518 drivers/usb/core/hub.c:5953
Fix by moving the card lifecycle out of usb6fire_chip_abort() and into
usb6fire_chip_disconnect(). The card pointer is saved in a local
before any teardown, snd_card_disconnect() is called first to prevent
new opens, URBs are aborted while chip is still valid, and
snd_card_free_when_closed() is called last so chip is never accessed
after the card may be freed. |
| In the Linux kernel, the following vulnerability has been resolved:
nilfs2: fix NULL i_assoc_inode dereference in nilfs_mdt_save_to_shadow_map
The DAT inode's btree node cache (i_assoc_inode) is initialized lazily
during btree operations. However, nilfs_mdt_save_to_shadow_map()
assumes i_assoc_inode is already initialized when copying dirty pages
to the shadow map during GC.
If NILFS_IOCTL_CLEAN_SEGMENTS is called immediately after mount before
any btree operation has occurred on the DAT inode, i_assoc_inode is
NULL leading to a general protection fault.
Fix this by calling nilfs_attach_btree_node_cache() on the DAT inode
in nilfs_dat_read() at mount time, ensuring i_assoc_inode is always
initialized before any GC operation can use it. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: btintel: serialize btintel_hw_error() with hci_req_sync_lock
btintel_hw_error() issues two __hci_cmd_sync() calls (HCI_OP_RESET
and Intel exception-info retrieval) without holding
hci_req_sync_lock(). This lets it race against
hci_dev_do_close() -> btintel_shutdown_combined(), which also runs
__hci_cmd_sync() under the same lock. When both paths manipulate
hdev->req_status/req_rsp concurrently, the close path may free the
response skb first, and the still-running hw_error path hits a
slab-use-after-free in kfree_skb().
Wrap the whole recovery sequence in hci_req_sync_lock/unlock so it
is serialized with every other synchronous HCI command issuer.
Below is the data race report and the kasan report:
BUG: data-race in __hci_cmd_sync_sk / btintel_shutdown_combined
read of hdev->req_rsp at net/bluetooth/hci_sync.c:199
by task kworker/u17:1/83:
__hci_cmd_sync_sk+0x12f2/0x1c30 net/bluetooth/hci_sync.c:200
__hci_cmd_sync+0x55/0x80 net/bluetooth/hci_sync.c:223
btintel_hw_error+0x114/0x670 drivers/bluetooth/btintel.c:254
hci_error_reset+0x348/0xa30 net/bluetooth/hci_core.c:1030
write/free by task ioctl/22580:
btintel_shutdown_combined+0xd0/0x360
drivers/bluetooth/btintel.c:3648
hci_dev_close_sync+0x9ae/0x2c10 net/bluetooth/hci_sync.c:5246
hci_dev_do_close+0x232/0x460 net/bluetooth/hci_core.c:526
BUG: KASAN: slab-use-after-free in
sk_skb_reason_drop+0x43/0x380 net/core/skbuff.c:1202
Read of size 4 at addr ffff888144a738dc
by task kworker/u17:1/83:
__hci_cmd_sync_sk+0x12f2/0x1c30 net/bluetooth/hci_sync.c:200
__hci_cmd_sync+0x55/0x80 net/bluetooth/hci_sync.c:223
btintel_hw_error+0x186/0x670 drivers/bluetooth/btintel.c:260 |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (pmbus/core) Protect regulator operations with mutex
The regulator operations pmbus_regulator_get_voltage(),
pmbus_regulator_set_voltage(), and pmbus_regulator_list_voltage()
access PMBus registers and shared data but were not protected by
the update_lock mutex. This could lead to race conditions.
However, adding mutex protection directly to these functions causes
a deadlock because pmbus_regulator_notify() (which calls
regulator_notifier_call_chain()) is often called with the mutex
already held (e.g., from pmbus_fault_handler()). If a regulator
callback then calls one of the now-protected voltage functions,
it will attempt to acquire the same mutex.
Rework pmbus_regulator_notify() to utilize a worker function to
send notifications outside of the mutex protection. Events are
stored as atomics in a per-page bitmask and processed by the worker.
Initialize the worker and its associated data during regulator
registration, and ensure it is cancelled on device removal using
devm_add_action_or_reset().
While at it, remove the unnecessary include of linux/of.h. |
