| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
fpga: region: fix use-after-free in child_regions_with_firmware()
Move of_node_put(child_region) after the error print to avoid accessing
freed memory when pr_err() references child_region.
[ Yilun: Fix the Fixes tag ] |
| In the Linux kernel, the following vulnerability has been resolved:
MIPS: DEC: Prevent initial console buffer from landing in XKPHYS
In 64-bit configurations calling the initial console output handler from
a kernel thread other than the initial one will result in a situation
where the stack has been placed in the XKPHYS 64-bit memory segment and
consequently so has been the buffer allocated there that is used as the
argument corresponding to the `%s' output conversion specifier for the
firmware's printf() entry point.
This 64-bit address will then be truncated by 32-bit firmware, resulting
in an attempt to access the wrong memory location, which in turn will
cause all kinds of unpredictable behaviour, such as a kernel crash:
Console: colour dummy device 160x64
Calibrating delay loop... 49.36 BogoMIPS (lpj=192512)
pid_max: default: 32768 minimum: 301
CPU 0 Unable to handle kernel paging request at virtual address 000000000203bd00, epc == ffffffffbfc08364, ra == ffffffffbfc08800
Oops[#1]:
CPU: 0 PID: 0 Comm: swapper Not tainted 5.18.0-rc2-00254-gfb649bda6f56-dirty #121
$ 0 : 0000000000000000 0000000000000001 0000000000000023 ffffffff80684ba0
$ 4 : 000000000203bd00 ffffffffbfc0f3b4 ffffffffffffffff 0000000000000073
$ 8 : 0a303d7469000000 0000000000000000 0000000000000073 ffffffffbfc0f473
$12 : 0000000000000002 0000000000000000 ffffffff80684c1c 0000000000000000
$16 : 0000000000000000 ffffffff80596dc9 0000000000000000 ffffffffbfc09240
$20 : ffffffff80684c40 ffffffffbfc0f400 000000000000002d 000000000000002b
$24 : ffffffffffffffbf 000000000203bd00
$28 : ffffffff805f0000 ffffffff80684b58 0000000000000030 ffffffffbfc08800
Hi : 0000000000000000
Lo : 0000000000000aa8
epc : ffffffffbfc08364 0xffffffffbfc08364
ra : ffffffffbfc08800 0xffffffffbfc08800
Status: 140120e2 KX SX UX KERNEL EXL
Cause : 00000008 (ExcCode 02)
BadVA : 000000000203bd00
PrId : 00000430 (R4000SC)
Modules linked in:
Process swapper (pid: 0, threadinfo=(____ptrval____), task=(____ptrval____), tls=0000000000000000)
Stack : 0000000000000000 0000000000000000 0000000000000000 0000004d0000004d
80684cc0806a2a40 80596dc80000004d 8061000000000000 bfc0850c80684c38
0000000000000000 000000000203bd00 0000000000000000 0000000000000000
0000000000000000 00000000bfc0f3b4 0000000000000000 0000000000000000
0000000000000000 0000000000000000 0000000000000000 0000000000000000
0000000000000000 0000000000000000 0000000000000000 0000000000000000
0000002500000000 0000000000000000 0000000000000000 802c1a7400000000
0203bd0080596dc8 0203bd4d69000000 6c61632000000018 5f746567646e6172
6c616320625f6d6f 5f736e5f6d6f7266 206361323778302b 303d74696e726320
806a0a38806b0000 806a0a38806b0000 00000000806b0000 80683c58806b0000
...
Call Trace:
Code: a082ffff 03e00008 00601021 <80820000> 00001821 10400005 24840001 80820000 24630001
---[ end trace 0000000000000000 ]---
Kernel panic - not syncing: Fatal exception in interrupt
KN04 V2.1k (PC: 0xa0026768, SP: 0x806848e8)
>>
In this case the pointer in $4 was truncated from 0x980000000203bd00 to
0x000000000203bd00.
This may happen when no final console driver has been enabled in the
configuration and consequently the initial console continues being used
late into bootstrap or with an upcoming change that will switch the zs
driver to use a platform device, which in turn will make the console
handover happen only after other kernel threads have already been
started.
Fix the issue by making the buffer static and initdata, and therefore
placed in the CKSEG0 32-bit compatibility segment, observing that the
console output handler is called with the console lock held, implying
no need for this code to be reentrant. Add an assertion to verify the
buffer actually has been placed in a compatibility segment. |
| Redis before 8.8.0, in the unusual case where an authenticated attacker can execute RESTORE, allows remote code execution via a RESTORE payload where the same NACK (pending entry) is referenced by more than one consumer, because deleting both consumers via XGROUP DELCONSUMER leads to a double free. NOTE: this issue exists because of an incomplete fix for CVE-2026-25243. |
| Knot Resolver before 6.4.1 allows remote code execution via a heap-based buffer overflow in the DoQ (DNS-over-QUIC) receive path. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: reject overlapping data areas in SMB2 responses
Commit 53b7c271f06b ("smb: client: restrict implied bcc[0] exemption to
responses without data area") restricted the implied bcc[0] length
exception to responses without a data area. However, the overlap
handling in __smb2_calc_size() clears data_length, which can make an
invalid response appear to have no data area and so qualify for the
exception.
Track data area overlap separately and reject such responses before
applying the length compatibility exceptions. |
| In the Linux kernel, the following vulnerability has been resolved:
fuse-uring: end fuse_req on io-uring cancel task work
When io_uring delivers task work with tw.cancel set (PF_EXITING,
PF_KTHREAD fallback, or percpu_ref_is_dying on the ring context),
fuse_uring_send_in_task() takes the cancel branch, assigns
-ECANCELED, and falls through to fuse_uring_send(). That path only
flips the entry to FRRS_USERSPACE and completes the io_uring cmd;
it never discharges the ring entry's owning reference to the
fuse_req that fuse_uring_add_req_to_ring_ent() handed it at
dispatch time.
fuse_uring_send_in_task()
tw.cancel == true
err = -ECANCELED
fuse_uring_send(ent, cmd, err, issue_flags)
ent->state = FRRS_USERSPACE
list_move(&ent->list, &queue->ent_in_userspace)
ent->cmd = NULL
io_uring_cmd_done(-ECANCELED)
/* ent->fuse_req still set, req still hashed */
The fuse_req stays linked on fpq->processing[hash] and
fuse_request_end() is never invoked. The originating syscall
thread blocks in D-state in request_wait_answer() until
fuse_abort_conn() runs, which can be the entire connection
lifetime. For FR_BACKGROUND requests fc->num_background is never
decremented either, so repeated cancels inflate the counter until
max_background is hit and all later background ops stall. tw.cancel does
not imply a connection abort (e.g. a single io_uring worker thread exits
while the fuse connection stays up), so this cannot be left for
fuse_abort_conn() to clean up.
Ending the req but still routing the entry through fuse_uring_send()
is not enough: that leaves a req-less entry on ent_in_userspace, and
ent_list_request_expired() dereferences ent->fuse_req unconditionally
on the head of that list, which would then NULL-deref.
Fix the cancel branch to release the entry directly. Remove it from the
queue, complete the io_uring cmd, end the fuse_req, free the entry, and
drop its queue_refs (waking the teardown waiter if it was the last). |
| In the Linux kernel, the following vulnerability has been resolved:
fuse-uring: fix EFAULT clobber in fuse_uring_commit
copy_from_user() returns the number of bytes not copied as an unsigned
residual on failure (1..sizeof(struct fuse_out_header)). fuse_uring_commit
stores that residual in ssize_t err, sets req->out.h.error to -EFAULT,
then jumps to out: with err still holding the positive residual.
err = copy_from_user(&req->out.h, &ent->headers->in_out,
sizeof(req->out.h));
if (err) {
req->out.h.error = -EFAULT;
goto out; /* err is the positive residual */
}
...
out:
fuse_uring_req_end(ent, req, err);
fuse_uring_req_end() then runs
if (error)
req->out.h.error = error;
which overwrites the just-assigned -EFAULT with the positive residual.
FUSE callers such as fuse_simple_request() test err < 0 to detect
failure, so the positive value is interpreted as success and the
caller proceeds with an uninitialised or partial req->out.args.
Fix by assigning err = -EFAULT in the failure branch before jumping
to out, so fuse_uring_req_end() receives a negative errno and sets
req->out.h.error to -EFAULT. |
| In the Linux kernel, the following vulnerability has been resolved:
fuse: avoid 32-bit prune notification count wrap
FUSE_NOTIFY_PRUNE validates the nodeid payload length with:
size - sizeof(outarg) != outarg.count * sizeof(u64)
On 32-bit kernels, size_t is also 32 bits, so the daemon-controlled
count multiplication can wrap. A prune notification with count
0x20000000 and no nodeid payload passes the check, enters the copy
loop, and asks the device copy path to read nodeids that are not
present in the userspace write buffer. In QEMU this reaches the
fuse_copy_fill() BUG_ON(!err) path.
Validate the payload length with array_size() instead. That accepts
exactly the same valid messages, but avoids wrapping arithmetic before
the copy loop consumes the count. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/siw: bound Read Response placement to the RREAD length
In drivers/infiniband/sw/siw/siw_qp_rx.c, siw_proc_rresp() places each
inbound Read Response DDP segment at sge->laddr + wqe->processed and then
accumulates wqe->processed, but it never checks the running total against
the sink buffer length on continuation segments. siw_check_sge() resolves
and validates the sink memory only on the first fragment (the if (!*mem)
branch), and siw_rresp_check_ntoh() compares the cumulative length against
wqe->bytes only on the final segment (the !frx->more_ddp_segs guard).
A connected siw peer that answers an outstanding RREAD with Read Response
segments that keep the DDP Last flag clear, carrying more total payload
than the RREAD requested, drives wqe->processed past the validated sink
buffer; the next siw_rx_data() call writes out of bounds at
sge->laddr + wqe->processed. siw runs iWARP over ordinary routable TCP,
so the peer is the remote end of an established RDMA connection and needs
no local privilege.
Bound every segment before placement, exactly as siw_proc_send() and
siw_proc_write() already do for their tagged and untagged paths, and
terminate the connection with a base-or-bounds DDP error when the
Read Response would overrun the sink buffer.
This is the second receive-path length fix for this file. A separate
change rejects an MPA FPDU length that underflows the per-fragment
remainder in the header decode; that guard does not cover this case,
because here each individual segment length is self-consistent and only
the accumulated placement offset overruns the buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: mms114 - reject an oversized device packet size
mms114_interrupt() reads a packet of touch data from the device into a
fixed-size on-stack buffer
struct mms114_touch touch[MMS114_MAX_TOUCH];
which holds MMS114_MAX_TOUCH (10) events of MMS114_EVENT_SIZE (8) bytes,
i.e. 80 bytes. The length of the I2C read into it is taken verbatim from
the device:
packet_size = mms114_read_reg(data, MMS114_PACKET_SIZE);
if (packet_size <= 0)
goto out;
...
error = __mms114_read_reg(data, MMS114_INFORMATION, packet_size,
(u8 *)touch);
packet_size is a single device register byte (0x0F) and the only check
is the lower bound packet_size <= 0; it is never bounded against the
size of touch[]. A malfunctioning, malicious or counterfeit controller
(or an attacker tampering with the I2C bus) can report a packet_size of
up to 255, so __mms114_read_reg() writes up to 175 bytes past the end of
touch[] on the IRQ-thread stack: a stack out-of-bounds write that can
overwrite the stack canary, saved registers and the return address.
A well-formed device never reports more than the buffer holds, so reject
an oversized packet and drop the report, consistent with the handler's
other error paths, rather than reading past the buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: touchwin - reset the packet index on every complete packet
tw_interrupt() accumulates each non-zero serial byte into a fixed
three-byte buffer with a running index that is only reset once a full
packet has been received *and* the device's two Y bytes agree:
tw->data[tw->idx++] = data;
if (tw->idx == TW_LENGTH && tw->data[1] == tw->data[2]) {
...
tw->idx = 0;
}
The reset is gated on tw->data[1] == tw->data[2], a value the device
controls. A malicious, malfunctioning or counterfeit Touchwindow
peripheral can stream non-zero bytes whose 2nd and 3rd bytes differ: the
index reaches TW_LENGTH without the equality holding, is never reset, and
keeps growing, so tw->data[tw->idx++] walks off the end of the three-byte
array and the rest of the heap-allocated struct tw, one attacker-chosen
byte at a time -- an unbounded, device-driven heap out-of-bounds write.
Reset the index on every completed packet and report an event only when
the two Y bytes match, like the other serio touchscreen drivers do. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: mms114 - fix touch indexing for MMS134S and MMS136
The MMS134S and MMS136 touch controllers have an event size of 6 bytes
rather than 8 bytes. When __mms114_read_reg() reads the touch data
packet from the device into the touch buffer, the events are packed
tightly at 6-byte intervals. However, the driver iterates through the
events using standard C array indexing (touch[index]), where each
element is sizeof(struct mms114_touch) (8 bytes) apart. As a result, any
touch events beyond the first one are read from incorrect offsets and
parsed improperly.
Fix this by explicitly calculating the byte offset for each touch event
based on the device's specific event size. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: goodix - clamp the device-reported contact count
goodix_ts_read_input_report() copies the number of touch points reported
by the device into an on-stack buffer
u8 point_data[2 + GOODIX_MAX_CONTACT_SIZE * GOODIX_MAX_CONTACTS];
which is sized for at most GOODIX_MAX_CONTACTS (10) contacts. The only
runtime check bounds the per-interrupt count against ts->max_touch_num,
but that value is taken verbatim from a 4-bit field of the device
configuration block and is never clamped:
ts->max_touch_num = ts->config[MAX_CONTACTS_LOC] & 0x0f;
The nibble can be 0..15, so a malfunctioning, malicious or counterfeit
controller (or an attacker tampering with the I2C bus) can advertise up
to 15 contacts. goodix_ts_read_input_report() then accepts a touch_num
of up to 15 and the second goodix_i2c_read() writes
ts->contact_size * (touch_num - 1) bytes past the one-contact header into
point_data - up to 30 bytes (45 with the 9-byte report format) beyond the
92-byte buffer: a stack out-of-bounds write.
Clamp max_touch_num to GOODIX_MAX_CONTACTS, the number of contacts
point_data[] is sized for, when reading it from the configuration. |
| In the Linux kernel, the following vulnerability has been resolved:
fpga: dfl-afu: validate DMA mapping length in afu_dma_map_region()
afu_ioctl_dma_map() accepts a 64-bit length from userspace via
DFL_FPGA_PORT_DMA_MAP ioctl without an upper bound check. The value
is passed to afu_dma_pin_pages() where npages is derived as
length >> PAGE_SHIFT and passed to pin_user_pages_fast() which takes
int nr_pages, causing implicit truncation if length is very large.
Validate map.length at the ioctl entry point before calling
afu_dma_map_region(), rejecting values whose page count exceeds
INT_MAX. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: SEV: Pin source page for write when adding CPUID data for SNP guest
When populating a guest_memfd instance with the initial CPUID data for an
SNP guest, acquire a writable pin on the source page as KVM will write back
the "correct" CPUID information if the userspace provided data is rejected
by trusted firmware. Because KVM writes to the source page using a kernel
mapping, pinning for read could result in KVM clobbering read-only memory.
Note, well-behaved VMMs are unlikely to be affected, as CPUID information
is almost always dynamically generated by userspace, i.e. it's unlikely for
the CPUID information to be backed by a read-only mapping.
[sean: rewrite shortlog and changelog, tag for stable@] |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: arm64: Bound used_lrs when flushing the pKVM hyp vCPU
flush_hyp_vcpu() copies the host vGIC state into the hyp's private vCPU
on every run. The vGIC list register save and restore use used_lrs as
their loop bound and expect it to stay within the number of implemented
list registers. While this is generally the case, flush_hyp_vcpu()
copies vgic_v3 verbatim and does not enforce this, so a value provided
by the host is used at EL2 to index vgic_lr[] and access ICH_LR<n>_EL2
(host -> EL2).
Fix by clamping used_lrs to the number of implemented list registers
after the copy, as the trusted path already does in
vgic_flush_lr_state(). The number of implemented list registers is
constant after init, so it is replicated once from
kvm_vgic_global_state.nr_lr into hyp_gicv3_nr_lr rather than read on
every entry. |
| In the Linux kernel, the following vulnerability has been resolved:
iommufd: Set upper bounds on cache invalidation entry_num and entry_len
iommufd_hwpt_invalidate() takes a user-controlled entry_num and entry_len,
each bounded only by U32_MAX. An entry_len beyond the kernel's struct size
makes the copy helper verify the extra bytes are zero, scanning that excess
in one uninterruptible pass; a multi-gigabyte value over zeroed user memory
trips the soft-lockup watchdog.
A large entry_num is the other half, driving the backend invalidation loop
with no reschedule. The VT-d nested handler, for one, copies each entry and
flushes caches per iteration, pinning the CPU on a non-preemptible kernel.
Cap both in the ioctl. entry_len is held under PAGE_SIZE, above any request
struct, and entry_num under 1 << 19, the order of a hardware invalidation
queue and well beyond any real batch, bounding the per-call loop length. |
| In the Linux kernel, the following vulnerability has been resolved:
iommufd: Move vevent memory allocation outside spinlock
The veventq memory allocation happens inside the spinlock. Given its depth
is decided by the user space, this leaves a vulnerability, where userspace
can allocate large queues to exhaust atomic memory reserves.
Move the allocation outside the spinlock and use GFP_NOWAIT, which can fail
fast under memory pressure without dipping into the GFP_ATOMIC reserves or
direct-reclaiming from the threaded IRQ handler. On allocation failure,
queue the lost_events_header (so userspace learns of the drop) and return
-ENOMEM so the caller learns of the kernel-side memory pressure.
This is intentionally distinct from the queue-overflow path, which also
queues the lost_events_header but returns 0: a full queue is an expected
userspace-pacing condition rather than a kernel error.
A subsequent change will cap the upper bound of the veventq_depth. |
| In the Linux kernel, the following vulnerability has been resolved:
mm: do file ownership checks with the proper mount idmap
Ever since idmapped mounts were introduced, inode ownership checks (for
side-channel protection) in mincore() and madvise(MADV_PAGEOUT) were done
against the nop_mnt_idmap, which completely ignores the file's mount's
idmap. This results in odd edgecases like:
1) mount/bind-mount with an idmap userA:userB:1
2) userB runs an owner_or_capable() check on file that is owned by userA
on-disk/in-memory, but owned by userB after idmap translation
3) owner_or_capable() mysteriously fails as the correct idmap wasn't supplied
In the case of mincore/madvise MADV_PAGEOUT, this is usually benign,
because file_permission(file, MAY_WRITE) will probably succeed, as it uses
the proper idmap internally, but it does not need to be the case on e.g a
0444 file where even the owner itself doesn't have permissions to write to
it.
Since this is clearly not trivial to get right, introduce a
file_owner_or_capable() that can carry the correct semantics, and switch
the various users in mm to it.
The issue was found by manual code inspection & an off-list discussion
with Jan Kara. |
| In the Linux kernel, the following vulnerability has been resolved:
regulator: scmi: fix of_node refcount leak in scmi_regulator_probe()
scmi_regulator_probe() calls of_find_node_by_name() which takes a
reference on the returned device node. On the error path where
process_scmi_regulator_of_node() fails, the function returns without
calling of_node_put() on the child node, leaking the reference.
Add of_node_put(np) on the error path to properly release the
reference. |
