| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
m68k: Only force 030 bus error if PC not in exception table
__get_kernel_nofault() does copy data in supervisor mode when
forcing a task backtrace log through /proc/sysrq_trigger.
This is expected cause a bus error exception on e.g. NULL
pointer dereferencing when logging a kernel task has no
workqueue associated. This bus error ought to be ignored.
Our 030 bus error handler is ill equipped to deal with this:
Whenever ssw indicates a kernel mode access on a data fault,
we don't even attempt to handle the fault and instead always
send a SEGV signal (or panic). As a result, the check
for exception handling at the fault PC (buried in
send_sig_fault() which gets called from do_page_fault()
eventually) is never used.
In contrast, both 040 and 060 access error handlers do not
care whether a fault happened on supervisor mode access,
and will call do_page_fault() on those, ultimately honoring
the exception table.
Add a check in bus_error030 to call do_page_fault() in case
we do have an entry for the fault PC in our exception table.
I had attempted a fix for this earlier in 2019 that did rely
on testing pagefault_disabled() (see link below) to achieve
the same thing, but this patch should be more generic.
Tested on 030 Atari Falcon. |
| In the Linux kernel, the following vulnerability has been resolved:
PCI/DOE: Fix destroy_work_on_stack() race
The following debug object splat was observed in testing:
ODEBUG: free active (active state 0) object: 0000000097d23782 object type: work_struct hint: doe_statemachine_work+0x0/0x510
WARNING: CPU: 1 PID: 71 at lib/debugobjects.c:514 debug_print_object+0x7d/0xb0
...
Workqueue: pci 0000:36:00.0 DOE [1 doe_statemachine_work
RIP: 0010:debug_print_object+0x7d/0xb0
...
Call Trace:
? debug_print_object+0x7d/0xb0
? __pfx_doe_statemachine_work+0x10/0x10
debug_object_free.part.0+0x11b/0x150
doe_statemachine_work+0x45e/0x510
process_one_work+0x1d4/0x3c0
This occurs because destroy_work_on_stack() was called after signaling
the completion in the calling thread. This creates a race between
destroy_work_on_stack() and the task->work struct going out of scope in
pci_doe().
Signal the work complete after destroying the work struct. This is safe
because signal_task_complete() is the final thing the work item does and
the workqueue code is careful not to access the work struct after. |
| In the Linux kernel, the following vulnerability has been resolved:
net/smc: fix potential panic dues to unprotected smc_llc_srv_add_link()
There is a certain chance to trigger the following panic:
PID: 5900 TASK: ffff88c1c8af4100 CPU: 1 COMMAND: "kworker/1:48"
#0 [ffff9456c1cc79a0] machine_kexec at ffffffff870665b7
#1 [ffff9456c1cc79f0] __crash_kexec at ffffffff871b4c7a
#2 [ffff9456c1cc7ab0] crash_kexec at ffffffff871b5b60
#3 [ffff9456c1cc7ac0] oops_end at ffffffff87026ce7
#4 [ffff9456c1cc7ae0] page_fault_oops at ffffffff87075715
#5 [ffff9456c1cc7b58] exc_page_fault at ffffffff87ad0654
#6 [ffff9456c1cc7b80] asm_exc_page_fault at ffffffff87c00b62
[exception RIP: ib_alloc_mr+19]
RIP: ffffffffc0c9cce3 RSP: ffff9456c1cc7c38 RFLAGS: 00010202
RAX: 0000000000000000 RBX: 0000000000000002 RCX: 0000000000000004
RDX: 0000000000000010 RSI: 0000000000000000 RDI: 0000000000000000
RBP: ffff88c1ea281d00 R8: 000000020a34ffff R9: ffff88c1350bbb20
R10: 0000000000000000 R11: 0000000000000001 R12: 0000000000000000
R13: 0000000000000010 R14: ffff88c1ab040a50 R15: ffff88c1ea281d00
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#7 [ffff9456c1cc7c60] smc_ib_get_memory_region at ffffffffc0aff6df [smc]
#8 [ffff9456c1cc7c88] smcr_buf_map_link at ffffffffc0b0278c [smc]
#9 [ffff9456c1cc7ce0] __smc_buf_create at ffffffffc0b03586 [smc]
The reason here is that when the server tries to create a second link,
smc_llc_srv_add_link() has no protection and may add a new link to
link group. This breaks the security environment protected by
llc_conf_mutex. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: ebtables: fix table blob use-after-free
We are not allowed to return an error at this point.
Looking at the code it looks like ret is always 0 at this
point, but its not.
t = find_table_lock(net, repl->name, &ret, &ebt_mutex);
... this can return a valid table, with ret != 0.
This bug causes update of table->private with the new
blob, but then frees the blob right away in the caller.
Syzbot report:
BUG: KASAN: vmalloc-out-of-bounds in __ebt_unregister_table+0xc00/0xcd0 net/bridge/netfilter/ebtables.c:1168
Read of size 4 at addr ffffc90005425000 by task kworker/u4:4/74
Workqueue: netns cleanup_net
Call Trace:
kasan_report+0xbf/0x1f0 mm/kasan/report.c:517
__ebt_unregister_table+0xc00/0xcd0 net/bridge/netfilter/ebtables.c:1168
ebt_unregister_table+0x35/0x40 net/bridge/netfilter/ebtables.c:1372
ops_exit_list+0xb0/0x170 net/core/net_namespace.c:169
cleanup_net+0x4ee/0xb10 net/core/net_namespace.c:613
...
ip(6)tables appears to be ok (ret should be 0 at this point) but make
this more obvious. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: codecs: tx-macro: Fix for KASAN: slab-out-of-bounds
When we run syzkaller we get below Out of Bound.
"KASAN: slab-out-of-bounds Read in regcache_flat_read"
Below is the backtrace of the issue:
dump_backtrace+0x0/0x4c8
show_stack+0x34/0x44
dump_stack_lvl+0xd8/0x118
print_address_description+0x30/0x2d8
kasan_report+0x158/0x198
__asan_report_load4_noabort+0x44/0x50
regcache_flat_read+0x10c/0x110
regcache_read+0xf4/0x180
_regmap_read+0xc4/0x278
_regmap_update_bits+0x130/0x290
regmap_update_bits_base+0xc0/0x15c
snd_soc_component_update_bits+0xa8/0x22c
snd_soc_component_write_field+0x68/0xd4
tx_macro_digital_mute+0xec/0x140
Actually There is no need to have decimator with 32 bits.
By limiting the variable with short type u8 issue is resolved. |
| In the Linux kernel, the following vulnerability has been resolved:
rcuscale: Move rcu_scale_writer() schedule_timeout_uninterruptible() to _idle()
The rcuscale.holdoff module parameter can be used to delay the start
of rcu_scale_writer() kthread. However, the hung-task timeout will
trigger when the timeout specified by rcuscale.holdoff is greater than
hung_task_timeout_secs:
runqemu kvm nographic slirp qemuparams="-smp 4 -m 2048M"
bootparams="rcuscale.shutdown=0 rcuscale.holdoff=300"
[ 247.071753] INFO: task rcu_scale_write:59 blocked for more than 122 seconds.
[ 247.072529] Not tainted 6.4.0-rc1-00134-gb9ed6de8d4ff #7
[ 247.073400] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 247.074331] task:rcu_scale_write state:D stack:30144 pid:59 ppid:2 flags:0x00004000
[ 247.075346] Call Trace:
[ 247.075660] <TASK>
[ 247.075965] __schedule+0x635/0x1280
[ 247.076448] ? __pfx___schedule+0x10/0x10
[ 247.076967] ? schedule_timeout+0x2dc/0x4d0
[ 247.077471] ? __pfx_lock_release+0x10/0x10
[ 247.078018] ? enqueue_timer+0xe2/0x220
[ 247.078522] schedule+0x84/0x120
[ 247.078957] schedule_timeout+0x2e1/0x4d0
[ 247.079447] ? __pfx_schedule_timeout+0x10/0x10
[ 247.080032] ? __pfx_rcu_scale_writer+0x10/0x10
[ 247.080591] ? __pfx_process_timeout+0x10/0x10
[ 247.081163] ? __pfx_sched_set_fifo_low+0x10/0x10
[ 247.081760] ? __pfx_rcu_scale_writer+0x10/0x10
[ 247.082287] rcu_scale_writer+0x6b1/0x7f0
[ 247.082773] ? mark_held_locks+0x29/0xa0
[ 247.083252] ? __pfx_rcu_scale_writer+0x10/0x10
[ 247.083865] ? __pfx_rcu_scale_writer+0x10/0x10
[ 247.084412] kthread+0x179/0x1c0
[ 247.084759] ? __pfx_kthread+0x10/0x10
[ 247.085098] ret_from_fork+0x2c/0x50
[ 247.085433] </TASK>
This commit therefore replaces schedule_timeout_uninterruptible() with
schedule_timeout_idle(). |
| In the Linux kernel, the following vulnerability has been resolved:
cifs: fix potential oops in cifs_oplock_break
With deferred close we can have closes that race with lease breaks,
and so with the current checks for whether to send the lease response,
oplock_response(), this can mean that an unmount (kill_sb) can occur
just before we were checking if the tcon->ses is valid. See below:
[Fri Aug 4 04:12:50 2023] RIP: 0010:cifs_oplock_break+0x1f7/0x5b0 [cifs]
[Fri Aug 4 04:12:50 2023] Code: 7d a8 48 8b 7d c0 c0 e9 02 48 89 45 b8 41 89 cf e8 3e f5 ff ff 4c 89 f7 41 83 e7 01 e8 82 b3 03 f2 49 8b 45 50 48 85 c0 74 5e <48> 83 78 60 00 74 57 45 84 ff 75 52 48 8b 43 98 48 83 eb 68 48 39
[Fri Aug 4 04:12:50 2023] RSP: 0018:ffffb30607ddbdf8 EFLAGS: 00010206
[Fri Aug 4 04:12:50 2023] RAX: 632d223d32612022 RBX: ffff97136944b1e0 RCX: 0000000080100009
[Fri Aug 4 04:12:50 2023] RDX: 0000000000000001 RSI: 0000000080100009 RDI: ffff97136944b188
[Fri Aug 4 04:12:50 2023] RBP: ffffb30607ddbe58 R08: 0000000000000001 R09: ffffffffc08e0900
[Fri Aug 4 04:12:50 2023] R10: 0000000000000001 R11: 000000000000000f R12: ffff97136944b138
[Fri Aug 4 04:12:50 2023] R13: ffff97149147c000 R14: ffff97136944b188 R15: 0000000000000000
[Fri Aug 4 04:12:50 2023] FS: 0000000000000000(0000) GS:ffff9714f7c00000(0000) knlGS:0000000000000000
[Fri Aug 4 04:12:50 2023] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[Fri Aug 4 04:12:50 2023] CR2: 00007fd8de9c7590 CR3: 000000011228e000 CR4: 0000000000350ef0
[Fri Aug 4 04:12:50 2023] Call Trace:
[Fri Aug 4 04:12:50 2023] <TASK>
[Fri Aug 4 04:12:50 2023] process_one_work+0x225/0x3d0
[Fri Aug 4 04:12:50 2023] worker_thread+0x4d/0x3e0
[Fri Aug 4 04:12:50 2023] ? process_one_work+0x3d0/0x3d0
[Fri Aug 4 04:12:50 2023] kthread+0x12a/0x150
[Fri Aug 4 04:12:50 2023] ? set_kthread_struct+0x50/0x50
[Fri Aug 4 04:12:50 2023] ret_from_fork+0x22/0x30
[Fri Aug 4 04:12:50 2023] </TASK>
To fix this change the ordering of the checks before sending the oplock_response
to first check if the openFileList is empty. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: Don't clone flow post action attributes second time
The code already clones post action attributes in
mlx5e_clone_flow_attr_for_post_act(). Creating another copy in
mlx5e_tc_post_act_add() is a erroneous leftover from original
implementation. Instead, assign handle->attribute to post_attr provided by
the caller. Note that cloning the attribute second time is not just
wasteful but also causes issues like second copy not being properly updated
in neigh update code which leads to following use-after-free:
Feb 21 09:02:00 c-237-177-40-045 kernel: BUG: KASAN: use-after-free in mlx5_cmd_set_fte+0x200d/0x24c0 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: kasan_report+0xbb/0x1a0
Feb 21 09:02:00 c-237-177-40-045 kernel: kasan_save_stack+0x1e/0x40
Feb 21 09:02:00 c-237-177-40-045 kernel: kasan_set_track+0x21/0x30
Feb 21 09:02:00 c-237-177-40-045 kernel: __kasan_kmalloc+0x7a/0x90
Feb 21 09:02:00 c-237-177-40-045 kernel: kasan_save_stack+0x1e/0x40
Feb 21 09:02:00 c-237-177-40-045 kernel: kasan_set_track+0x21/0x30
Feb 21 09:02:00 c-237-177-40-045 kernel: kasan_save_free_info+0x2a/0x40
Feb 21 09:02:00 c-237-177-40-045 kernel: ____kasan_slab_free+0x11a/0x1b0
Feb 21 09:02:00 c-237-177-40-045 kernel: page dumped because: kasan: bad access detected
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5_core 0000:08:00.0: mlx5_cmd_out_err:803:(pid 8833): SET_FLOW_TABLE_ENTRY(0x936) op_mod(0x0) failed, status bad resource state(0x9), syndrome (0xf2ff71), err(-22)
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5_core 0000:08:00.0 enp8s0f0: Failed to add post action rule
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5_core 0000:08:00.0: mlx5e_tc_encap_flows_add:190:(pid 8833): Failed to update flow post acts, -22
Feb 21 09:02:00 c-237-177-40-045 kernel: Call Trace:
Feb 21 09:02:00 c-237-177-40-045 kernel: <TASK>
Feb 21 09:02:00 c-237-177-40-045 kernel: dump_stack_lvl+0x57/0x7d
Feb 21 09:02:00 c-237-177-40-045 kernel: print_report+0x170/0x471
Feb 21 09:02:00 c-237-177-40-045 kernel: ? mlx5_cmd_set_fte+0x200d/0x24c0 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: kasan_report+0xbb/0x1a0
Feb 21 09:02:00 c-237-177-40-045 kernel: ? mlx5_cmd_set_fte+0x200d/0x24c0 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5_cmd_set_fte+0x200d/0x24c0 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: ? __module_address.part.0+0x62/0x200
Feb 21 09:02:00 c-237-177-40-045 kernel: ? mlx5_cmd_stub_create_flow_table+0xd0/0xd0 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: ? __raw_spin_lock_init+0x3b/0x110
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5_cmd_create_fte+0x80/0xb0 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: add_rule_fg+0xe80/0x19c0 [mlx5_core]
--
Feb 21 09:02:00 c-237-177-40-045 kernel: Allocated by task 13476:
Feb 21 09:02:00 c-237-177-40-045 kernel: kasan_save_stack+0x1e/0x40
Feb 21 09:02:00 c-237-177-40-045 kernel: kasan_set_track+0x21/0x30
Feb 21 09:02:00 c-237-177-40-045 kernel: __kasan_kmalloc+0x7a/0x90
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5_packet_reformat_alloc+0x7b/0x230 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5e_tc_tun_create_header_ipv4+0x977/0xf10 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5e_attach_encap+0x15b4/0x1e10 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: post_process_attr+0x305/0xa30 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5e_tc_add_fdb_flow+0x4c0/0xcf0 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: __mlx5e_add_fdb_flow+0x7cf/0xe90 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5e_configure_flower+0xcaa/0x4b90 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5e_rep_setup_tc_cls_flower+0x99/0x1b0 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5e_rep_setup_tc_cb+0x133/0x1e0 [mlx5_core]
--
Feb 21 09:02:00 c-237-177-40-045 kernel: Freed by task 8833:
Feb 21 09:02:00 c-237-177-40-045 kernel: kasan_save_s
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
powerpc/pseries: Rework lppaca_shared_proc() to avoid DEBUG_PREEMPT
lppaca_shared_proc() takes a pointer to the lppaca which is typically
accessed through get_lppaca(). With DEBUG_PREEMPT enabled, this leads
to checking if preemption is enabled, for example:
BUG: using smp_processor_id() in preemptible [00000000] code: grep/10693
caller is lparcfg_data+0x408/0x19a0
CPU: 4 PID: 10693 Comm: grep Not tainted 6.5.0-rc3 #2
Call Trace:
dump_stack_lvl+0x154/0x200 (unreliable)
check_preemption_disabled+0x214/0x220
lparcfg_data+0x408/0x19a0
...
This isn't actually a problem however, as it does not matter which
lppaca is accessed, the shared proc state will be the same.
vcpudispatch_stats_procfs_init() already works around this by disabling
preemption, but the lparcfg code does not, erroring any time
/proc/powerpc/lparcfg is accessed with DEBUG_PREEMPT enabled.
Instead of disabling preemption on the caller side, rework
lppaca_shared_proc() to not take a pointer and instead directly access
the lppaca, bypassing any potential preemption checks.
[mpe: Rework to avoid needing a definition in paca.h and lppaca.h] |
| In the Linux kernel, the following vulnerability has been resolved:
debugobjects: Don't wake up kswapd from fill_pool()
syzbot is reporting a lockdep warning in fill_pool() because the allocation
from debugobjects is using GFP_ATOMIC, which is (__GFP_HIGH | __GFP_KSWAPD_RECLAIM)
and therefore tries to wake up kswapd, which acquires kswapd_wait::lock.
Since fill_pool() might be called with arbitrary locks held, fill_pool()
should not assume that acquiring kswapd_wait::lock is safe.
Use __GFP_HIGH instead and remove __GFP_NORETRY as it is pointless for
!__GFP_DIRECT_RECLAIM allocation. |
| In the Linux kernel, the following vulnerability has been resolved:
fbdev: udlfb: Fix endpoint check
The syzbot fuzzer detected a problem in the udlfb driver, caused by an
endpoint not having the expected type:
usb 1-1: Read EDID byte 0 failed: -71
usb 1-1: Unable to get valid EDID from device/display
------------[ cut here ]------------
usb 1-1: BOGUS urb xfer, pipe 3 != type 1
WARNING: CPU: 0 PID: 9 at drivers/usb/core/urb.c:504 usb_submit_urb+0xed6/0x1880
drivers/usb/core/urb.c:504
Modules linked in:
CPU: 0 PID: 9 Comm: kworker/0:1 Not tainted
6.4.0-rc1-syzkaller-00016-ga4422ff22142 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google
04/28/2023
Workqueue: usb_hub_wq hub_event
RIP: 0010:usb_submit_urb+0xed6/0x1880 drivers/usb/core/urb.c:504
...
Call Trace:
<TASK>
dlfb_submit_urb+0x92/0x180 drivers/video/fbdev/udlfb.c:1980
dlfb_set_video_mode+0x21f0/0x2950 drivers/video/fbdev/udlfb.c:315
dlfb_ops_set_par+0x2a7/0x8d0 drivers/video/fbdev/udlfb.c:1111
dlfb_usb_probe+0x149a/0x2710 drivers/video/fbdev/udlfb.c:1743
The current approach for this issue failed to catch the problem
because it only checks for the existence of a bulk-OUT endpoint; it
doesn't check whether this endpoint is the one that the driver will
actually use.
We can fix the problem by instead checking that the endpoint used by
the driver does exist and is bulk-OUT. |
| In the Linux kernel, the following vulnerability has been resolved:
s390/vmem: split pages when debug pagealloc is enabled
Since commit bb1520d581a3 ("s390/mm: start kernel with DAT enabled")
the kernel crashes early during boot when debug pagealloc is enabled:
mem auto-init: stack:off, heap alloc:off, heap free:off
addressing exception: 0005 ilc:2 [#1] SMP DEBUG_PAGEALLOC
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 6.5.0-rc3-09759-gc5666c912155 #630
[..]
Krnl Code: 00000000001325f6: ec5600248064 cgrj %r5,%r6,8,000000000013263e
00000000001325fc: eb880002000c srlg %r8,%r8,2
#0000000000132602: b2210051 ipte %r5,%r1,%r0,0
>0000000000132606: b90400d1 lgr %r13,%r1
000000000013260a: 41605008 la %r6,8(%r5)
000000000013260e: a7db1000 aghi %r13,4096
0000000000132612: b221006d ipte %r6,%r13,%r0,0
0000000000132616: e3d0d0000171 lay %r13,4096(%r13)
Call Trace:
__kernel_map_pages+0x14e/0x320
__free_pages_ok+0x23a/0x5a8)
free_low_memory_core_early+0x214/0x2c8
memblock_free_all+0x28/0x58
mem_init+0xb6/0x228
mm_core_init+0xb6/0x3b0
start_kernel+0x1d2/0x5a8
startup_continue+0x36/0x40
Kernel panic - not syncing: Fatal exception: panic_on_oops
This is caused by using large mappings on machines with EDAT1/EDAT2. Add
the code to split the mappings into 4k pages if debug pagealloc is enabled
by CONFIG_DEBUG_PAGEALLOC_ENABLE_DEFAULT or the debug_pagealloc kernel
command line option. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Address KCSAN report on bpf_lru_list
KCSAN reported a data-race when accessing node->ref.
Although node->ref does not have to be accurate,
take this chance to use a more common READ_ONCE() and WRITE_ONCE()
pattern instead of data_race().
There is an existing bpf_lru_node_is_ref() and bpf_lru_node_set_ref().
This patch also adds bpf_lru_node_clear_ref() to do the
WRITE_ONCE(node->ref, 0) also.
==================================================================
BUG: KCSAN: data-race in __bpf_lru_list_rotate / __htab_lru_percpu_map_update_elem
write to 0xffff888137038deb of 1 bytes by task 11240 on cpu 1:
__bpf_lru_node_move kernel/bpf/bpf_lru_list.c:113 [inline]
__bpf_lru_list_rotate_active kernel/bpf/bpf_lru_list.c:149 [inline]
__bpf_lru_list_rotate+0x1bf/0x750 kernel/bpf/bpf_lru_list.c:240
bpf_lru_list_pop_free_to_local kernel/bpf/bpf_lru_list.c:329 [inline]
bpf_common_lru_pop_free kernel/bpf/bpf_lru_list.c:447 [inline]
bpf_lru_pop_free+0x638/0xe20 kernel/bpf/bpf_lru_list.c:499
prealloc_lru_pop kernel/bpf/hashtab.c:290 [inline]
__htab_lru_percpu_map_update_elem+0xe7/0x820 kernel/bpf/hashtab.c:1316
bpf_percpu_hash_update+0x5e/0x90 kernel/bpf/hashtab.c:2313
bpf_map_update_value+0x2a9/0x370 kernel/bpf/syscall.c:200
generic_map_update_batch+0x3ae/0x4f0 kernel/bpf/syscall.c:1687
bpf_map_do_batch+0x2d9/0x3d0 kernel/bpf/syscall.c:4534
__sys_bpf+0x338/0x810
__do_sys_bpf kernel/bpf/syscall.c:5096 [inline]
__se_sys_bpf kernel/bpf/syscall.c:5094 [inline]
__x64_sys_bpf+0x43/0x50 kernel/bpf/syscall.c:5094
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
read to 0xffff888137038deb of 1 bytes by task 11241 on cpu 0:
bpf_lru_node_set_ref kernel/bpf/bpf_lru_list.h:70 [inline]
__htab_lru_percpu_map_update_elem+0x2f1/0x820 kernel/bpf/hashtab.c:1332
bpf_percpu_hash_update+0x5e/0x90 kernel/bpf/hashtab.c:2313
bpf_map_update_value+0x2a9/0x370 kernel/bpf/syscall.c:200
generic_map_update_batch+0x3ae/0x4f0 kernel/bpf/syscall.c:1687
bpf_map_do_batch+0x2d9/0x3d0 kernel/bpf/syscall.c:4534
__sys_bpf+0x338/0x810
__do_sys_bpf kernel/bpf/syscall.c:5096 [inline]
__se_sys_bpf kernel/bpf/syscall.c:5094 [inline]
__x64_sys_bpf+0x43/0x50 kernel/bpf/syscall.c:5094
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
value changed: 0x01 -> 0x00
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 11241 Comm: syz-executor.3 Not tainted 6.3.0-rc7-syzkaller-00136-g6a66fdd29ea1 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 03/30/2023
================================================================== |
| In the Linux kernel, the following vulnerability has been resolved:
bcache: fixup btree_cache_wait list damage
We get a kernel crash about "list_add corruption. next->prev should be
prev (ffff9c801bc01210), but was ffff9c77b688237c.
(next=ffffae586d8afe68)."
crash> struct list_head 0xffff9c801bc01210
struct list_head {
next = 0xffffae586d8afe68,
prev = 0xffffae586d8afe68
}
crash> struct list_head 0xffff9c77b688237c
struct list_head {
next = 0x0,
prev = 0x0
}
crash> struct list_head 0xffffae586d8afe68
struct list_head struct: invalid kernel virtual address: ffffae586d8afe68 type: "gdb_readmem_callback"
Cannot access memory at address 0xffffae586d8afe68
[230469.019492] Call Trace:
[230469.032041] prepare_to_wait+0x8a/0xb0
[230469.044363] ? bch_btree_keys_free+0x6c/0xc0 [escache]
[230469.056533] mca_cannibalize_lock+0x72/0x90 [escache]
[230469.068788] mca_alloc+0x2ae/0x450 [escache]
[230469.080790] bch_btree_node_get+0x136/0x2d0 [escache]
[230469.092681] bch_btree_check_thread+0x1e1/0x260 [escache]
[230469.104382] ? finish_wait+0x80/0x80
[230469.115884] ? bch_btree_check_recurse+0x1a0/0x1a0 [escache]
[230469.127259] kthread+0x112/0x130
[230469.138448] ? kthread_flush_work_fn+0x10/0x10
[230469.149477] ret_from_fork+0x35/0x40
bch_btree_check_thread() and bch_dirty_init_thread() may call
mca_cannibalize() to cannibalize other cached btree nodes. Only one thread
can do it at a time, so the op of other threads will be added to the
btree_cache_wait list.
We must call finish_wait() to remove op from btree_cache_wait before free
it's memory address. Otherwise, the list will be damaged. Also should call
bch_cannibalize_unlock() to release the btree_cache_alloc_lock and wake_up
other waiters. |
| In the Linux kernel, the following vulnerability has been resolved:
mtd: spi-nor: Fix shift-out-of-bounds in spi_nor_set_erase_type
spi_nor_set_erase_type() was used either to set or to mask out an erase
type. When we used it to mask out an erase type a shift-out-of-bounds
was hit:
UBSAN: shift-out-of-bounds in drivers/mtd/spi-nor/core.c:2237:24
shift exponent 4294967295 is too large for 32-bit type 'int'
The setting of the size_{shift, mask} and of the opcode are unnecessary
when the erase size is zero, as throughout the code just the erase size
is considered to determine whether an erase type is supported or not.
Setting the opcode to 0xFF was wrong too as nobody guarantees that 0xFF
is an unused opcode. Thus when masking out an erase type, just set the
erase size to zero. This will fix the shift-out-of-bounds.
[ta: refine changes, new commit message, fix compilation error] |
| In the Linux kernel, the following vulnerability has been resolved:
thermal: intel: quark_dts: fix error pointer dereference
If alloc_soc_dts() fails, then we can just return. Trying to free
"soc_dts" will lead to an Oops. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/irdma: Fix data race on CQP completion stats
CQP completion statistics is read lockesly in irdma_wait_event and
irdma_check_cqp_progress while it can be updated in the completion
thread irdma_sc_ccq_get_cqe_info on another CPU as KCSAN reports.
Make completion statistics an atomic variable to reflect coherent updates
to it. This will also avoid load/store tearing logic bug potentially
possible by compiler optimizations.
[77346.170861] BUG: KCSAN: data-race in irdma_handle_cqp_op [irdma] / irdma_sc_ccq_get_cqe_info [irdma]
[77346.171383] write to 0xffff8a3250b108e0 of 8 bytes by task 9544 on cpu 4:
[77346.171483] irdma_sc_ccq_get_cqe_info+0x27a/0x370 [irdma]
[77346.171658] irdma_cqp_ce_handler+0x164/0x270 [irdma]
[77346.171835] cqp_compl_worker+0x1b/0x20 [irdma]
[77346.172009] process_one_work+0x4d1/0xa40
[77346.172024] worker_thread+0x319/0x700
[77346.172037] kthread+0x180/0x1b0
[77346.172054] ret_from_fork+0x22/0x30
[77346.172136] read to 0xffff8a3250b108e0 of 8 bytes by task 9838 on cpu 2:
[77346.172234] irdma_handle_cqp_op+0xf4/0x4b0 [irdma]
[77346.172413] irdma_cqp_aeq_cmd+0x75/0xa0 [irdma]
[77346.172592] irdma_create_aeq+0x390/0x45a [irdma]
[77346.172769] irdma_rt_init_hw.cold+0x212/0x85d [irdma]
[77346.172944] irdma_probe+0x54f/0x620 [irdma]
[77346.173122] auxiliary_bus_probe+0x66/0xa0
[77346.173137] really_probe+0x140/0x540
[77346.173154] __driver_probe_device+0xc7/0x220
[77346.173173] driver_probe_device+0x5f/0x140
[77346.173190] __driver_attach+0xf0/0x2c0
[77346.173208] bus_for_each_dev+0xa8/0xf0
[77346.173225] driver_attach+0x29/0x30
[77346.173240] bus_add_driver+0x29c/0x2f0
[77346.173255] driver_register+0x10f/0x1a0
[77346.173272] __auxiliary_driver_register+0xbc/0x140
[77346.173287] irdma_init_module+0x55/0x1000 [irdma]
[77346.173460] do_one_initcall+0x7d/0x410
[77346.173475] do_init_module+0x81/0x2c0
[77346.173491] load_module+0x1232/0x12c0
[77346.173506] __do_sys_finit_module+0x101/0x180
[77346.173522] __x64_sys_finit_module+0x3c/0x50
[77346.173538] do_syscall_64+0x39/0x90
[77346.173553] entry_SYSCALL_64_after_hwframe+0x63/0xcd
[77346.173634] value changed: 0x0000000000000094 -> 0x0000000000000095 |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: message: mptlan: Fix use after free bug in mptlan_remove() due to race condition
mptlan_probe() calls mpt_register_lan_device() which initializes the
&priv->post_buckets_task workqueue. A call to
mpt_lan_wake_post_buckets_task() will subsequently start the work.
During driver unload in mptlan_remove() the following race may occur:
CPU0 CPU1
|mpt_lan_post_receive_buckets_work()
mptlan_remove() |
free_netdev() |
kfree(dev); |
|
| dev->mtu
| //use
Fix this by finishing the work prior to cleaning up in mptlan_remove().
[mkp: we really should remove mptlan instead of attempting to fix it] |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: qat - fix out-of-bounds read
When preparing an AER-CTR request, the driver copies the key provided by
the user into a data structure that is accessible by the firmware.
If the target device is QAT GEN4, the key size is rounded up by 16 since
a rounded up size is expected by the device.
If the key size is rounded up before the copy, the size used for copying
the key might be bigger than the size of the region containing the key,
causing an out-of-bounds read.
Fix by doing the copy first and then update the keylen.
This is to fix the following warning reported by KASAN:
[ 138.150574] BUG: KASAN: global-out-of-bounds in qat_alg_skcipher_init_com.isra.0+0x197/0x250 [intel_qat]
[ 138.150641] Read of size 32 at addr ffffffff88c402c0 by task cryptomgr_test/2340
[ 138.150651] CPU: 15 PID: 2340 Comm: cryptomgr_test Not tainted 6.2.0-rc1+ #45
[ 138.150659] Hardware name: Intel Corporation ArcherCity/ArcherCity, BIOS EGSDCRB1.86B.0087.D13.2208261706 08/26/2022
[ 138.150663] Call Trace:
[ 138.150668] <TASK>
[ 138.150922] kasan_check_range+0x13a/0x1c0
[ 138.150931] memcpy+0x1f/0x60
[ 138.150940] qat_alg_skcipher_init_com.isra.0+0x197/0x250 [intel_qat]
[ 138.151006] qat_alg_skcipher_init_sessions+0xc1/0x240 [intel_qat]
[ 138.151073] crypto_skcipher_setkey+0x82/0x160
[ 138.151085] ? prepare_keybuf+0xa2/0xd0
[ 138.151095] test_skcipher_vec_cfg+0x2b8/0x800 |
| A vulnerability was detected in PKrystian Full-Stack-Bank up to bf73a0179e3ff07c0d7dc35297cea0be0e5b1317. This vulnerability affects unknown code of the component User Handler. Performing manipulation results in sql injection. It is possible to initiate the attack remotely. This product is using a rolling release to provide continious delivery. Therefore, no version details for affected nor updated releases are available. The patch is named 25c9965a872c704f3a9475488dc5d3196902199a. It is suggested to install a patch to address this issue. |
