In the Linux kernel, the following vulnerability has been resolved:
spi: spi-qpic-snand: write the feature value before executing SET_FEATURE
qcom_spi_send_cmdaddr() programs NAND_FLASH_CMD/NAND_EXEC_CMD and submits
the descriptors, which makes the controller execute the command
immediately. For SPINAND_SET_FEATURE the value to be written is only
placed into NAND_FLASH_FEATURES afterwards, by qcom_spi_io_op(), in a
second submission - so the chip is programmed with whatever that register
happened to hold from a previous operation, and the intended value is only
applied by the *next* SET_FEATURE.
Measured on a TP-Link Archer AX55 v1 (IPQ5018, ESMT F50L1G41LB): writing
0x40 to the configuration register (0xb0) leaves the chip at 0x00, and the
subsequent write of 0x00 leaves it at 0x40 - every write lands one
operation late.
This stayed unnoticed until v6.18 added SPI-NAND OTP support together
with OTP entries for ESMT chips. spinand_otp_rw() enables OTP mode,
reads, and disables it again, and mtd_otp_nvmem_add() does this during
MTD registration. With the off-by-one, the "disable" write actually
applies the previously requested value, so CFG_OTP_ENABLE ends up set:
the chip stays in OTP mode, every subsequent array read returns the OTP
area instead of the array (UBI reports an empty device) and all writes
fail with -EIO because the OTP area is write protected. On this board
that makes the whole flash unusable and the device unbootable.
Write the feature value into NAND_FLASH_FEATURES as part of the same
transaction, before NAND_EXEC_CMD. While at it, copy only the bytes the
operation actually carries - the previous code dereferenced a 4-byte
pointer on a one-byte buffer (spinand->scratchbuf).
With this patch the flash contents read back bit-identical to a
known-good dump of the same board taken under the vendor firmware
(md5-verified across partitions), and writes work.
spi: spi-qpic-snand: write the feature value before executing SET_FEATURE
qcom_spi_send_cmdaddr() programs NAND_FLASH_CMD/NAND_EXEC_CMD and submits
the descriptors, which makes the controller execute the command
immediately. For SPINAND_SET_FEATURE the value to be written is only
placed into NAND_FLASH_FEATURES afterwards, by qcom_spi_io_op(), in a
second submission - so the chip is programmed with whatever that register
happened to hold from a previous operation, and the intended value is only
applied by the *next* SET_FEATURE.
Measured on a TP-Link Archer AX55 v1 (IPQ5018, ESMT F50L1G41LB): writing
0x40 to the configuration register (0xb0) leaves the chip at 0x00, and the
subsequent write of 0x00 leaves it at 0x40 - every write lands one
operation late.
This stayed unnoticed until v6.18 added SPI-NAND OTP support together
with OTP entries for ESMT chips. spinand_otp_rw() enables OTP mode,
reads, and disables it again, and mtd_otp_nvmem_add() does this during
MTD registration. With the off-by-one, the "disable" write actually
applies the previously requested value, so CFG_OTP_ENABLE ends up set:
the chip stays in OTP mode, every subsequent array read returns the OTP
area instead of the array (UBI reports an empty device) and all writes
fail with -EIO because the OTP area is write protected. On this board
that makes the whole flash unusable and the device unbootable.
Write the feature value into NAND_FLASH_FEATURES as part of the same
transaction, before NAND_EXEC_CMD. While at it, copy only the bytes the
operation actually carries - the previous code dereferenced a 4-byte
pointer on a one-byte buffer (spinand->scratchbuf).
With this patch the flash contents read back bit-identical to a
known-good dump of the same board taken under the vendor firmware
(md5-verified across partitions), and writes work.
Default status is the baseline for the product, each version can override it (e.g. patched versions marked unaffected).
| Vendor | Product | Default status | Versions | ||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Linux | Linux | unaffected |
|
||||||||||||||||||
| Linux | Linux | affected |
|
No data.
No data.
No data.
Advisories
No advisories yet.
Fixes
Solution
No solution given by the vendor.
Workaround
No workaround given by the vendor.
References
History
Fri, 28 Aug 2026 07:30:00 +0000
| Type | Values Removed | Values Added |
|---|---|---|
| Description | In the Linux kernel, the following vulnerability has been resolved: spi: spi-qpic-snand: write the feature value before executing SET_FEATURE qcom_spi_send_cmdaddr() programs NAND_FLASH_CMD/NAND_EXEC_CMD and submits the descriptors, which makes the controller execute the command immediately. For SPINAND_SET_FEATURE the value to be written is only placed into NAND_FLASH_FEATURES afterwards, by qcom_spi_io_op(), in a second submission - so the chip is programmed with whatever that register happened to hold from a previous operation, and the intended value is only applied by the *next* SET_FEATURE. Measured on a TP-Link Archer AX55 v1 (IPQ5018, ESMT F50L1G41LB): writing 0x40 to the configuration register (0xb0) leaves the chip at 0x00, and the subsequent write of 0x00 leaves it at 0x40 - every write lands one operation late. This stayed unnoticed until v6.18 added SPI-NAND OTP support together with OTP entries for ESMT chips. spinand_otp_rw() enables OTP mode, reads, and disables it again, and mtd_otp_nvmem_add() does this during MTD registration. With the off-by-one, the "disable" write actually applies the previously requested value, so CFG_OTP_ENABLE ends up set: the chip stays in OTP mode, every subsequent array read returns the OTP area instead of the array (UBI reports an empty device) and all writes fail with -EIO because the OTP area is write protected. On this board that makes the whole flash unusable and the device unbootable. Write the feature value into NAND_FLASH_FEATURES as part of the same transaction, before NAND_EXEC_CMD. While at it, copy only the bytes the operation actually carries - the previous code dereferenced a 4-byte pointer on a one-byte buffer (spinand->scratchbuf). With this patch the flash contents read back bit-identical to a known-good dump of the same board taken under the vendor firmware (md5-verified across partitions), and writes work. | |
| Title | spi: spi-qpic-snand: write the feature value before executing SET_FEATURE | |
| First Time appeared |
Linux
Linux linux Kernel |
|
| CPEs | cpe:2.3:o:linux:linux_kernel:*:*:*:*:*:*:*:* | |
| Vendors & Products |
Linux
Linux linux Kernel |
|
| References |
|
Projects
Sign in to view the affected projects.
MITRE
Status: PUBLISHED
Assigner: Linux
Published:
Updated: 2026-08-28T06:53:11.243Z
Reserved: 2026-08-26T14:34:25.788Z
Link: CVE-2026-80712
Vulnrichment
No data.
NVD
Status : Received
Published: 2026-08-28T08:16:56.850
Modified: 2026-08-28T08:16:56.850
Link: CVE-2026-80712
Redhat
No data.
OpenCVE Enrichment
No data.
Weaknesses
No weakness.