| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: endpoint: pci-epf-ntb: Remove duplicate resource teardown
epf_ntb_epc_destroy() duplicates the teardown that the caller is
supposed to do later. This leads to an oops when .allow_link fails or
when .drop_link is performed. Remove the helper.
Also drop pci_epc_put(). EPC device refcounting is tied to configfs EPC
group lifetime, and pci_epc_put() in the .drop_link path is sufficient. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/nouveau: fix u32 overflow in pushbuf reloc bounds check
nouveau_gem_pushbuf_reloc_apply() validates each relocation with
if (r->reloc_bo_offset + 4 > nvbo->bo.base.size)
but reloc_bo_offset is __u32 (uapi/drm/nouveau_drm.h) and the integer
literal 4 promotes to unsigned int, so the addition is performed in 32
bits and wraps before the comparison against the size_t bo size.
Cast to u64 so the addition happens in 64-bit arithmetic.
[ Add Fixes: tag. - Danilo ] |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: caiaq: Handle probe errors properly
The probe procedure of setup_card() in caiaq driver doesn't treat the
error cases gracefully, e.g. the error from snd_card_register() calls
snd_card_free() but continues. This would lead to a UAF for the
further calls like snd_usb_caiaq_control_init(), as Berk suggested in
another patch in the link below.
However, the problem is not only that; in general, this function drops
the all error handlings (as it's a void function) although its caller
can propagate an error to snd_probe(), which eventually calls
snd_card_free() as a proper error path. That said, we should treat
each error case in setup_card(), and just return the error code
promptly, which is then handled later as a fatal error in snd_probe().
This patch achieves it by changing the setup_card() to return an error
code. Also, the superfluous snd_card_free() call is removed, too.
Note that card->private_free can be set still safely at returning an
error. All called functions in card_free() have checks of the
unassigned resources or NULL checks. |
| In the Linux kernel, the following vulnerability has been resolved:
ext2: reject inodes with zero i_nlink and valid mode in ext2_iget()
ext2_iget() already rejects inodes with i_nlink == 0 when i_mode is
zero or i_dtime is set, treating them as deleted. However, the case of
i_nlink == 0 with a non-zero mode and zero dtime slips through. Since
ext2 has no orphan list, such a combination can only result from
filesystem corruption - a legitimate inode deletion always sets either
i_dtime or clears i_mode before freeing the inode.
A crafted image can exploit this gap to present such an inode to the
VFS, which then triggers WARN_ON inside drop_nlink() (fs/inode.c) via
ext2_unlink(), ext2_rename() and ext2_rmdir():
WARNING: CPU: 3 PID: 609 at fs/inode.c:336 drop_nlink+0xad/0xd0 fs/inode.c:336
CPU: 3 UID: 0 PID: 609 Comm: syz-executor Not tainted 6.12.77+ #1
Call Trace:
<TASK>
inode_dec_link_count include/linux/fs.h:2518 [inline]
ext2_unlink+0x26c/0x300 fs/ext2/namei.c:295
vfs_unlink+0x2fc/0x9b0 fs/namei.c:4477
do_unlinkat+0x53e/0x730 fs/namei.c:4541
__x64_sys_unlink+0xc6/0x110 fs/namei.c:4587
do_syscall_64+0xf5/0x220 arch/x86/entry/common.c:78
entry_SYSCALL_64_after_hwframe+0x77/0x7f
</TASK>
WARNING: CPU: 0 PID: 646 at fs/inode.c:336 drop_nlink+0xad/0xd0 fs/inode.c:336
CPU: 0 UID: 0 PID: 646 Comm: syz.0.17 Not tainted 6.12.77+ #1
Call Trace:
<TASK>
inode_dec_link_count include/linux/fs.h:2518 [inline]
ext2_rename+0x35e/0x850 fs/ext2/namei.c:374
vfs_rename+0xf2f/0x2060 fs/namei.c:5021
do_renameat2+0xbe2/0xd50 fs/namei.c:5178
__x64_sys_rename+0x7e/0xa0 fs/namei.c:5223
do_syscall_64+0xf5/0x220 arch/x86/entry/common.c:78
entry_SYSCALL_64_after_hwframe+0x77/0x7f
</TASK>
WARNING: CPU: 0 PID: 634 at fs/inode.c:336 drop_nlink+0xad/0xd0 fs/inode.c:336
CPU: 0 UID: 0 PID: 634 Comm: syz-executor Not tainted 6.12.77+ #1
Call Trace:
<TASK>
inode_dec_link_count include/linux/fs.h:2518 [inline]
ext2_rmdir+0xca/0x110 fs/ext2/namei.c:311
vfs_rmdir+0x204/0x690 fs/namei.c:4348
do_rmdir+0x372/0x3e0 fs/namei.c:4407
__x64_sys_unlinkat+0xf0/0x130 fs/namei.c:4577
do_syscall_64+0xf5/0x220 arch/x86/entry/common.c:78
entry_SYSCALL_64_after_hwframe+0x77/0x7f
</TASK>
Extend the existing i_nlink == 0 check to also catch this case,
reporting the corruption via ext2_error() and returning -EFSCORRUPTED.
This rejects the inode at load time and prevents it from reaching any
of the namei.c paths.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: sd: fix missing put_disk() when device_add(&disk_dev) fails
If device_add(&sdkp->disk_dev) fails, put_device() runs
scsi_disk_release(), which frees the scsi_disk but leaves the gendisk
referenced. The device_add_disk() error path in sd_probe() calls
put_disk(gd); call put_disk(gd) here to mirror that cleanup. |
| In the Linux kernel, the following vulnerability has been resolved:
ibmasm: fix OOB reads in command_file_write due to missing size checks
The command_file_write() handler allocates a kernel buffer of exactly
count bytes and copies user data into it, but does not validate the
buffer against the dot command protocol before passing it to
get_dot_command_size() and get_dot_command_timeout().
Since both the allocation size (count) and the header fields (command_size,
data_size) are independently user-controlled, an attacker can cause
get_dot_command_size() to return a value exceeding the allocation,
triggering OOB reads in get_dot_command_timeout() and an out-of-bounds
memcpy_toio() that leaks kernel heap memory to the service processor.
Fix with two guards: reject writes smaller than sizeof(struct
dot_command_header) before allocation, then after copying user data
reject commands where the buffer is smaller than the total size declared
by the header (sizeof(header) + command_size + data_size). This ensures
all subsequent header and payload field accesses stay within the buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: caiaq: Fix potentially leftover ep1_in_urb at error path
The previous fix for handling the error from setup_card() missed that
an internal URB cdev->ep1_in_urb might have been already submitted
beforehand. In the normal case, this URB gets killed at the
disconnection, but in the error path, we didn't do it, hence there can
be a potential leak.
Fix it in the error path for setup_card(), too. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: nSVM: Sync interrupt shadow to cached vmcb12 after VMRUN of L2
After VMRUN in guest mode, nested_sync_control_from_vmcb02() syncs
fields written by the CPU from vmcb02 to the cached vmcb12. This is
because the cached vmcb12 is used as the authoritative copy of some of
the controls, and is the payload when saving/restoring nested state.
int_state is also written by the CPU, specifically bit 0 (i.e.
SVM_INTERRUPT_SHADOW_MASK) for nested VMs, but it is not sync'd to
cached vmcb12. This does not cause a problem if KVM_SET_NESTED_STATE
preceeds KVM_SET_VCPU_EVENTS in the restore path, as an interrupt shadow
would be correctly restored to vmcb02 (KVM_SET_VCPU_EVENTS overwrites
what KVM_SET_NESTED_STATE restored in int_state).
However, if KVM_SET_VCPU_EVENTS preceeds KVM_SET_NESTED_STATE, an
interrupt shadow would be restored into vmcb01 instead of vmcb02. This
would mostly be benign for L1 (delays an interrupt), but not for L2. For
L2, the vCPU could hang (e.g. if a wakeup interrupt is delivered before
a HLT that should have been in an interrupt shadow).
Sync int_state to the cached vmcb12 in nested_sync_control_from_vmcb02()
to avoid this problem. With that, KVM_SET_NESTED_STATE restores the
correct interrupt shadow state, and if KVM_SET_VCPU_EVENTS follows it
would overwrite it with the same value. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: ccree - fix a memory leak in cc_mac_digest()
Add cc_unmap_result() if cc_map_hash_request_final()
fails to prevent potential memory leak. |
| In the Linux kernel, the following vulnerability has been resolved:
bareudp: fix NULL pointer dereference in bareudp_fill_metadata_dst()
bareudp_fill_metadata_dst() passes bareudp->sock to
udp_tunnel6_dst_lookup() in the IPv6 path without a NULL check.
The socket is only created in bareudp_open() and NULLed in
bareudp_stop(), so calling this function while the device is down
triggers a NULL dereference via sock->sk.
BUG: kernel NULL pointer dereference, address: 0000000000000018
RIP: 0010:udp_tunnel6_dst_lookup (net/ipv6/ip6_udp_tunnel.c:160)
Call Trace:
<TASK>
bareudp_fill_metadata_dst (drivers/net/bareudp.c:532)
do_execute_actions (net/openvswitch/actions.c:901)
ovs_execute_actions (net/openvswitch/actions.c:1589)
ovs_packet_cmd_execute (net/openvswitch/datapath.c:700)
genl_family_rcv_msg_doit (net/netlink/genetlink.c:1114)
genl_rcv_msg (net/netlink/genetlink.c:1209)
netlink_rcv_skb (net/netlink/af_netlink.c:2550)
</TASK>
Add a NULL check returning -ESHUTDOWN, consistent with the xmit paths
in the same driver. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: arp_tables: fix IEEE1394 ARP payload parsing
Weiming Shi says:
"arp_packet_match() unconditionally parses the ARP payload assuming two
hardware addresses are present (source and target). However,
IPv4-over-IEEE1394 ARP (RFC 2734) omits the target hardware address
field, and arp_hdr_len() already accounts for this by returning a
shorter length for ARPHRD_IEEE1394 devices.
As a result, on IEEE1394 interfaces arp_packet_match() advances past a
nonexistent target hardware address and reads the wrong bytes for both
the target device address comparison and the target IP address. This
causes arptables rules to match against garbage data, leading to
incorrect filtering decisions: packets that should be accepted may be
dropped and vice versa.
The ARP stack in net/ipv4/arp.c (arp_create and arp_process) already
handles this correctly by skipping the target hardware address for
ARPHRD_IEEE1394. Apply the same pattern to arp_packet_match()."
Mangle the original patch to always return 0 (no match) in case user
matches on the target hardware address which is never present in
IEEE1394.
Note that this returns 0 (no match) for either normal and inverse match
because matching in the target hardware address in ARPHRD_IEEE1394 has
never been supported by arptables. This is intentional, matching on the
target hardware address should never evaluate true for ARPHRD_IEEE1394.
Moreover, adjust arpt_mangle to drop the packet too as AI suggests:
In arpt_mangle, the logic assumes a standard ARP layout. Because
IEEE1394 (FireWire) omits the target hardware address, the linear
pointer arithmetic miscalculates the offset for the target IP address.
This causes mangling operations to write to the wrong location, leading
to packet corruption. To ensure safety, this patch drops packets
(NF_DROP) when mangling is requested for these fields on IEEE1394
devices, as the current implementation cannot correctly map the FireWire
ARP payload.
This omits both mangling target hardware and IP address. Even if IP
address mangling should be possible in IEEE1394, this would require
to adjust arpt_mangle offset calculation, which has never been
supported.
Based on patch from Weiming Shi <bestswngs@gmail.com>. |
| In the Linux kernel, the following vulnerability has been resolved:
slip: bound decode() reads against the compressed packet length
slhc_uncompress() parses a VJ-compressed TCP header by advancing a
pointer through the packet via decode() and pull16(). Neither helper
bounds-checks against isize, and decode() masks its return with
& 0xffff so it can never return the -1 that callers test for -- those
error paths are dead code.
A short compressed frame whose change byte requests optional fields
lets decode() read past the end of the packet. The over-read bytes
are folded into the cached cstate and reflected into subsequent
reconstructed packets.
Make decode() and pull16() take the packet end pointer and return -1
when exhausted. Add a bounds check before the TCP-checksum read.
The existing == -1 tests now do what they were always meant to. |
| In the Linux kernel, the following vulnerability has been resolved:
slip: reject VJ receive packets on instances with no rstate array
slhc_init() accepts rslots == 0 as a valid configuration, with the
documented meaning of 'no receive compression'. In that case the
allocation loop in slhc_init() is skipped, so comp->rstate stays
NULL and comp->rslot_limit stays 0 (from the kzalloc of struct
slcompress).
The receive helpers do not defend against that configuration.
slhc_uncompress() dereferences comp->rstate[x] when the VJ header
carries an explicit connection ID, and slhc_remember() later assigns
cs = &comp->rstate[...] after only comparing the packet's slot number
to comp->rslot_limit. Because rslot_limit is 0, slot 0 passes the
range check, and the code dereferences a NULL rstate.
The configuration is reachable in-tree through PPP. PPPIOCSMAXCID
stores its argument in a signed int, and (val >> 16) uses arithmetic
shift. Passing 0xffff0000 therefore sign-extends to -1, so val2 + 1
is 0 and ppp_generic.c ends up calling slhc_init(0, 1). Because
/dev/ppp open is gated by ns_capable(CAP_NET_ADMIN), the whole path
is reachable from an unprivileged user namespace. Once the malformed
VJ state is installed, any inbound VJ-compressed or VJ-uncompressed
frame that selects slot 0 crashes the kernel in softirq context:
Oops: general protection fault, probably for non-canonical
address 0xdffffc0000000000: 0000 [#1] SMP KASAN NOPTI
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
RIP: 0010:slhc_uncompress (drivers/net/slip/slhc.c:519)
Call Trace:
<TASK>
ppp_receive_nonmp_frame (drivers/net/ppp/ppp_generic.c:2466)
ppp_input (drivers/net/ppp/ppp_generic.c:2359)
ppp_async_process (drivers/net/ppp/ppp_async.c:492)
tasklet_action_common (kernel/softirq.c:926)
handle_softirqs (kernel/softirq.c:623)
run_ksoftirqd (kernel/softirq.c:1055)
smpboot_thread_fn (kernel/smpboot.c:160)
kthread (kernel/kthread.c:436)
ret_from_fork (arch/x86/kernel/process.c:164)
</TASK>
Reject the receive side on such instances instead of touching rstate.
slhc_uncompress() falls through to its existing 'bad' label, which
bumps sls_i_error and enters the toss state. slhc_remember() mirrors
that with an explicit sls_i_error increment followed by slhc_toss();
the sls_i_runt counter is not used here because a missing rstate is
an internal configuration state, not a runt packet.
The transmit path is unaffected: the only in-tree caller that picks
rslots from userspace (ppp_generic.c) still supplies tslots >= 1, and
slip.c always calls slhc_init(16, 16), so comp->tstate remains valid
and slhc_compress() continues to work. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nfnetlink_osf: fix divide-by-zero in OSF_WSS_MODULO
nf_osf_match_one() computes ctx->window % f->wss.val in the
OSF_WSS_MODULO branch with no guard for f->wss.val == 0. A
CAP_NET_ADMIN user can add such a fingerprint via nfnetlink; a
subsequent matching TCP SYN divides by zero and panics the kernel.
Reject the bogus fingerprint in nfnl_osf_add_callback() above the
per-option for-loop. f->wss is per-fingerprint, not per-option, so
the check must run regardless of f->opt_num (including 0). Also
reject wss.wc >= OSF_WSS_MAX; nf_osf_match_one() already treats that
as "should not happen".
Crash:
Oops: divide error: 0000 [#1] SMP KASAN NOPTI
RIP: 0010:nf_osf_match_one (net/netfilter/nfnetlink_osf.c:98)
Call Trace:
<IRQ>
nf_osf_match (net/netfilter/nfnetlink_osf.c:220)
xt_osf_match_packet (net/netfilter/xt_osf.c:32)
ipt_do_table (net/ipv4/netfilter/ip_tables.c:348)
nf_hook_slow (net/netfilter/core.c:622)
ip_local_deliver (net/ipv4/ip_input.c:265)
ip_rcv (include/linux/skbuff.h:1162)
__netif_receive_skb_one_core (net/core/dev.c:6181)
process_backlog (net/core/dev.c:6642)
__napi_poll (net/core/dev.c:7710)
net_rx_action (net/core/dev.c:7945)
handle_softirqs (kernel/softirq.c:622) |
| In the Linux kernel, the following vulnerability has been resolved:
openvswitch: cap upcall PID array size and pre-size vport replies
The vport netlink reply helpers allocate a fixed-size skb with
nlmsg_new(NLMSG_DEFAULT_SIZE, ...) but serialize the full upcall PID
array via ovs_vport_get_upcall_portids(). Since
ovs_vport_set_upcall_portids() accepts any non-zero multiple of
sizeof(u32) with no upper bound, a CAP_NET_ADMIN user can install a PID
array large enough to overflow the reply buffer, causing nla_put() to
fail with -EMSGSIZE and hitting BUG_ON(err < 0). On systems with
unprivileged user namespaces enabled (e.g., Ubuntu default), this is
reachable via unshare -Urn since OVS vport mutation operations use
GENL_UNS_ADMIN_PERM.
kernel BUG at net/openvswitch/datapath.c:2414!
Oops: invalid opcode: 0000 [#1] SMP KASAN NOPTI
CPU: 1 UID: 0 PID: 65 Comm: poc Not tainted 7.0.0-rc7-00195-geb216e422044 #1
RIP: 0010:ovs_vport_cmd_set+0x34c/0x400
Call Trace:
<TASK>
genl_family_rcv_msg_doit (net/netlink/genetlink.c:1116)
genl_rcv_msg (net/netlink/genetlink.c:1194)
netlink_rcv_skb (net/netlink/af_netlink.c:2550)
genl_rcv (net/netlink/genetlink.c:1219)
netlink_unicast (net/netlink/af_netlink.c:1344)
netlink_sendmsg (net/netlink/af_netlink.c:1894)
__sys_sendto (net/socket.c:2206)
__x64_sys_sendto (net/socket.c:2209)
do_syscall_64 (arch/x86/entry/syscall_64.c:63)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130)
</TASK>
Kernel panic - not syncing: Fatal exception
Reject attempts to set more PIDs than nr_cpu_ids in
ovs_vport_set_upcall_portids(), and pre-compute the worst-case reply
size in ovs_vport_cmd_msg_size() based on that bound, similar to the
existing ovs_dp_cmd_msg_size(). nr_cpu_ids matches the cap already
used by the per-CPU dispatch configuration on the datapath side
(ovs_dp_cmd_fill_info() serialises at most nr_cpu_ids PIDs), so the
two sides stay consistent. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: reject negative CO-RE accessor indices in bpf_core_parse_spec()
CO-RE accessor strings are colon-separated indices that describe a path
from a root BTF type to a target field, e.g. "0:1:2" walks through
nested struct members. bpf_core_parse_spec() parses each component with
sscanf("%d"), so negative values like -1 are silently accepted. The
subsequent bounds checks (access_idx >= btf_vlen(t)) only guard the
upper bound and always pass for negative values because C integer
promotion converts the __u16 btf_vlen result to int, making the
comparison (int)(-1) >= (int)(N) false for any positive N.
When -1 reaches btf_member_bit_offset() it gets cast to u32 0xffffffff,
producing an out-of-bounds read far past the members array. A crafted
BPF program with a negative CO-RE accessor on any struct that exists in
vmlinux BTF (e.g. task_struct) crashes the kernel deterministically
during BPF_PROG_LOAD on any system with CONFIG_DEBUG_INFO_BTF=y
(default on major distributions). The bug is reachable with CAP_BPF:
BUG: unable to handle page fault for address: ffffed11818b6626
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
Oops: Oops: 0000 [#1] SMP KASAN NOPTI
CPU: 0 UID: 0 PID: 85 Comm: poc Not tainted 7.0.0-rc6 #18 PREEMPT(full)
RIP: 0010:bpf_core_parse_spec (tools/lib/bpf/relo_core.c:354)
RAX: 00000000ffffffff
Call Trace:
<TASK>
bpf_core_calc_relo_insn (tools/lib/bpf/relo_core.c:1321)
bpf_core_apply (kernel/bpf/btf.c:9507)
check_core_relo (kernel/bpf/verifier.c:19475)
bpf_check (kernel/bpf/verifier.c:26031)
bpf_prog_load (kernel/bpf/syscall.c:3089)
__sys_bpf (kernel/bpf/syscall.c:6228)
</TASK>
CO-RE accessor indices are inherently non-negative (struct member index,
array element index, or enumerator index), so reject them immediately
after parsing. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: fix end-of-list detection in cgroup_storage_get_next_key()
list_next_entry() never returns NULL -- when the current element is the
last entry it wraps to the list head via container_of(). The subsequent
NULL check is therefore dead code and get_next_key() never returns
-ENOENT for the last element, instead reading storage->key from a bogus
pointer that aliases internal map fields and copying the result to
userspace.
Replace it with list_entry_is_head() so the function correctly returns
-ENOENT when there are no more entries. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: L2CAP: Fix null-ptr-deref in l2cap_sock_get_sndtimeo_cb()
Add the same NULL guard already present in
l2cap_sock_resume_cb() and l2cap_sock_ready_cb(). |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: L2CAP: Fix null-ptr-deref in l2cap_sock_new_connection_cb()
Add the same NULL guard already present in
l2cap_sock_resume_cb() and l2cap_sock_ready_cb(). |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: L2CAP: Fix null-ptr-deref in l2cap_sock_state_change_cb()
Add the same NULL guard already present in
l2cap_sock_resume_cb() and l2cap_sock_ready_cb(). |
