| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: reject mount if bigalloc with s_first_data_block != 0
bigalloc with s_first_data_block != 0 is not supported, reject mounting
it. |
| In the Linux kernel, the following vulnerability has been resolved:
comedi: ni_atmio16d: Fix invalid clean-up after failed attach
If the driver's COMEDI "attach" handler function (`atmio16d_attach()`)
returns an error, the COMEDI core will call the driver's "detach"
handler function (`atmio16d_detach()`) to clean up. This calls
`reset_atmio16d()` unconditionally, but depending on where the error
occurred in the attach handler, the device may not have been
sufficiently initialized to call `reset_atmio16d()`. It uses
`dev->iobase` as the I/O port base address and `dev->private` as the
pointer to the COMEDI device's private data structure. `dev->iobase`
may still be set to its initial value of 0, which would result in
undesired writes to low I/O port addresses. `dev->private` may still be
`NULL`, which would result in null pointer dereferences.
Fix `atmio16d_detach()` by checking that `dev->private` is valid
(non-null) before calling `reset_atmio16d()`. This implies that
`dev->iobase` was set correctly since that is set up before
`dev->private`. |
| In the Linux kernel, the following vulnerability has been resolved:
comedi: runflags cannot determine whether to reclaim chanlist
syzbot reported a memory leak [1], because commit 4e1da516debb ("comedi:
Add reference counting for Comedi command handling") did not consider
the exceptional exit case in do_cmd_ioctl() where runflags is not set.
This caused chanlist not to be properly freed by do_become_nonbusy(),
as it only frees chanlist when runflags is correctly set.
Added a check in do_become_nonbusy() for the case where runflags is not
set, to properly free the chanlist memory.
[1]
BUG: memory leak
backtrace (crc 844a0efa):
__comedi_get_user_chanlist drivers/comedi/comedi_fops.c:1815 [inline]
do_cmd_ioctl.part.0+0x112/0x350 drivers/comedi/comedi_fops.c:1890
do_cmd_ioctl drivers/comedi/comedi_fops.c:1858 [inline] |
| In the Linux kernel, the following vulnerability has been resolved:
comedi: dt2815: add hardware detection to prevent crash
The dt2815 driver crashes when attached to I/O ports without actual
hardware present. This occurs because syzkaller or users can attach
the driver to arbitrary I/O addresses via COMEDI_DEVCONFIG ioctl.
When no hardware exists at the specified port, inb() operations return
0xff (floating bus), but outb() operations can trigger page faults due
to undefined behavior, especially under race conditions:
BUG: unable to handle page fault for address: 000000007fffff90
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
RIP: 0010:dt2815_attach+0x6e0/0x1110
Add hardware detection by reading the status register before attempting
any write operations. If the read returns 0xff, assume no hardware is
present and fail the attach with -ENODEV. This prevents crashes from
outb() operations on non-existent hardware. |
| In the Linux kernel, the following vulnerability has been resolved:
bridge: br_nd_send: validate ND option lengths
br_nd_send() walks ND options according to option-provided lengths.
A malformed option can make the parser advance beyond the computed
option span or use a too-short source LLADDR option payload.
Validate option lengths against the remaining NS option area before
advancing, and only read source LLADDR when the option is large enough
for an Ethernet address. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: core: Mitigate potential OOB by removing bogus memset()
The memset() in hid_report_raw_event() has the good intention of
clearing out bogus data by zeroing the area from the end of the incoming
data string to the assumed end of the buffer. However, as we have
previously seen, doing so can easily result in OOB reads and writes in
the subsequent thread of execution.
The current suggestion from one of the HID maintainers is to remove the
memset() and simply return if the incoming event buffer size is not
large enough to fill the associated report.
Suggested-by Benjamin Tissoires <bentiss@kernel.org>
[bentiss: changed the return value] |
| In the Linux kernel, the following vulnerability has been resolved:
HID: logitech-hidpp: Prevent use-after-free on force feedback initialisation failure
Presently, if the force feedback initialisation fails when probing the
Logitech G920 Driving Force Racing Wheel for Xbox One, an error number
will be returned and propagated before the userspace infrastructure
(sysfs and /dev/input) has been torn down. If userspace ignores the
errors and continues to use its references to these dangling entities, a
UAF will promptly follow.
We have 2 options; continue to return the error, but ensure that all of
the infrastructure is torn down accordingly or continue to treat this
condition as a warning by emitting the message but returning success.
It is thought that the original author's intention was to emit the
warning but keep the device functional, less the force feedback feature,
so let's go with that. |
| In the Linux kernel, the following vulnerability has been resolved:
net: mana: fix use-after-free in add_adev() error path
If auxiliary_device_add() fails, add_adev() jumps to add_fail and calls
auxiliary_device_uninit(adev).
The auxiliary device has its release callback set to adev_release(),
which frees the containing struct mana_adev. Since adev is embedded in
struct mana_adev, the subsequent fall-through to init_fail and access
to adev->id may result in a use-after-free.
Fix this by saving the allocated auxiliary device id in a local
variable before calling auxiliary_device_add(), and use that saved id
in the cleanup path after auxiliary_device_uninit(). |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: tegra - Add missing CRYPTO_ALG_ASYNC
The tegra crypto driver failed to set the CRYPTO_ALG_ASYNC on its
asynchronous algorithms, causing the crypto API to select them for users
that request only synchronous algorithms. This causes crashes (at
least). Fix this by adding the flag like what the other drivers do.
Also remove the unnecessary CRYPTO_ALG_TYPE_* flags, since those just
get ignored and overridden by the registration function anyway. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: target: file: Use kzalloc_flex for aio_cmd
The target_core_file doesn't initialize the aio_cmd->iocb for the
ki_write_stream. When a write command fd_execute_rw_aio() is executed,
we may get a bogus ki_write_stream value, causing unintended write
failure status when checking iocb->ki_write_stream > max_write_streams
in the block device.
Let's just use kzalloc_flex when allocating the aio_cmd and let
ki_write_stream=0 to fix this issue. |
| In the Linux kernel, the following vulnerability has been resolved:
vxlan: validate ND option lengths in vxlan_na_create
vxlan_na_create() walks ND options according to option-provided
lengths. A malformed option can make the parser advance beyond the
computed option span or use a too-short source LLADDR option payload.
Validate option lengths against the remaining NS option area before
advancing, and only read source LLADDR when the option is large enough
for an Ethernet address. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: avoid infinite loops caused by residual data
On the mkdir/mknod path, when mapping logical blocks to physical blocks,
if inserting a new extent into the extent tree fails (in this example,
because the file system disabled the huge file feature when marking the
inode as dirty), ext4_ext_map_blocks() only calls ext4_free_blocks() to
reclaim the physical block without deleting the corresponding data in
the extent tree. This causes subsequent mkdir operations to reference
the previously reclaimed physical block number again, even though this
physical block is already being used by the xattr block. Therefore, a
situation arises where both the directory and xattr are using the same
buffer head block in memory simultaneously.
The above causes ext4_xattr_block_set() to enter an infinite loop about
"inserted" and cannot release the inode lock, ultimately leading to the
143s blocking problem mentioned in [1].
If the metadata is corrupted, then trying to remove some extent space
can do even more harm. Also in case EXT4_GET_BLOCKS_DELALLOC_RESERVE
was passed, remove space wrongly update quota information.
Jan Kara suggests distinguishing between two cases:
1) The error is ENOSPC or EDQUOT - in this case the filesystem is fully
consistent and we must maintain its consistency including all the
accounting. However these errors can happen only early before we've
inserted the extent into the extent tree. So current code works correctly
for this case.
2) Some other error - this means metadata is corrupted. We should strive to
do as few modifications as possible to limit damage. So I'd just skip
freeing of allocated blocks.
[1]
INFO: task syz.0.17:5995 blocked for more than 143 seconds.
Call Trace:
inode_lock_nested include/linux/fs.h:1073 [inline]
__start_dirop fs/namei.c:2923 [inline]
start_dirop fs/namei.c:2934 [inline] |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: check if ext_caps is valid in BL setup
LVDS connectors don't have extended backlight caps so check
if the pointer is valid before accessing it.
(cherry picked from commit 3f797396d7f4eb9bb6eded184bbc6f033628a6f6) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Fix drm_edid leak in amdgpu_dm
[WHAT]
When a sink is connected, aconnector->drm_edid was overwritten without
freeing the previous allocation, causing a memory leak on resume.
[HOW]
Free the previous drm_edid before updating it.
(cherry picked from commit 52024a94e7111366141cfc5d888b2ef011f879e5) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: prevent immediate PASID reuse case
PASID resue could cause interrupt issue when process
immediately runs into hw state left by previous
process exited with the same PASID, it's possible that
page faults are still pending in the IH ring buffer when
the process exits and frees up its PASID. To prevent the
case, it uses idr cyclic allocator same as kernel pid's.
(cherry picked from commit 8f1de51f49be692de137c8525106e0fce2d1912d) |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: ibmvfc: Fix OOB access in ibmvfc_discover_targets_done()
A malicious or compromised VIO server can return a num_written value in the
discover targets MAD response that exceeds max_targets. This value is
stored directly in vhost->num_targets without validation, and is then used
as the loop bound in ibmvfc_alloc_targets() to index into disc_buf[], which
is only allocated for max_targets entries. Indices at or beyond max_targets
access kernel memory outside the DMA-coherent allocation. The
out-of-bounds data is subsequently embedded in Implicit Logout and PLOGI
MADs that are sent back to the VIO server, leaking kernel memory.
Fix by clamping num_written to max_targets before storing it. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: target: tcm_loop: Drain commands in target_reset handler
tcm_loop_target_reset() violates the SCSI EH contract: it returns SUCCESS
without draining any in-flight commands. The SCSI EH documentation
(scsi_eh.rst) requires that when a reset handler returns SUCCESS the driver
has made lower layers "forget about timed out scmds" and is ready for new
commands. Every other SCSI LLD (virtio_scsi, mpt3sas, ipr, scsi_debug,
mpi3mr) enforces this by draining or completing outstanding commands before
returning SUCCESS.
Because tcm_loop_target_reset() doesn't drain, the SCSI EH reuses in-flight
scsi_cmnd structures for recovery commands (e.g. TUR) while the target core
still has async completion work queued for the old se_cmd. The memset in
queuecommand zeroes se_lun and lun_ref_active, causing
transport_lun_remove_cmd() to skip its percpu_ref_put(). The leaked LUN
reference prevents transport_clear_lun_ref() from completing, hanging
configfs LUN unlink forever in D-state:
INFO: task rm:264 blocked for more than 122 seconds.
rm D 0 264 258 0x00004000
Call Trace:
__schedule+0x3d0/0x8e0
schedule+0x36/0xf0
transport_clear_lun_ref+0x78/0x90 [target_core_mod]
core_tpg_remove_lun+0x28/0xb0 [target_core_mod]
target_fabric_port_unlink+0x50/0x60 [target_core_mod]
configfs_unlink+0x156/0x1f0 [configfs]
vfs_unlink+0x109/0x290
do_unlinkat+0x1d5/0x2d0
Fix this by making tcm_loop_target_reset() actually drain commands:
1. Issue TMR_LUN_RESET via tcm_loop_issue_tmr() to drain all commands that
the target core knows about (those not yet CMD_T_COMPLETE).
2. Use blk_mq_tagset_busy_iter() to iterate all started requests and
flush_work() on each se_cmd — this drains any deferred completion work
for commands that already had CMD_T_COMPLETE set before the TMR (which
the TMR skips via __target_check_io_state()). This is the same pattern
used by mpi3mr, scsi_debug, and libsas to drain outstanding commands
during reset. |
| In the Linux kernel, the following vulnerability has been resolved:
writeback: don't block sync for filesystems with no data integrity guarantees
Add a SB_I_NO_DATA_INTEGRITY superblock flag for filesystems that cannot
guarantee data persistence on sync (eg fuse). For superblocks with this
flag set, sync kicks off writeback of dirty inodes but does not wait
for the flusher threads to complete the writeback.
This replaces the per-inode AS_NO_DATA_INTEGRITY mapping flag added in
commit f9a49aa302a0 ("fs/writeback: skip AS_NO_DATA_INTEGRITY mappings
in wait_sb_inodes()"). The flag belongs at the superblock level because
data integrity is a filesystem-wide property, not a per-inode one.
Having this flag at the superblock level also allows us to skip having
to iterate every dirty inode in wait_sb_inodes() only to skip each inode
individually.
Prior to this commit, mappings with no data integrity guarantees skipped
waiting on writeback completion but still waited on the flusher threads
to finish initiating the writeback. Waiting on the flusher threads is
unnecessary. This commit kicks off writeback but does not wait on the
flusher threads. This change properly addresses a recent report [1] for
a suspend-to-RAM hang seen on fuse-overlayfs that was caused by waiting
on the flusher threads to finish:
Workqueue: pm_fs_sync pm_fs_sync_work_fn
Call Trace:
<TASK>
__schedule+0x457/0x1720
schedule+0x27/0xd0
wb_wait_for_completion+0x97/0xe0
sync_inodes_sb+0xf8/0x2e0
__iterate_supers+0xdc/0x160
ksys_sync+0x43/0xb0
pm_fs_sync_work_fn+0x17/0xa0
process_one_work+0x193/0x350
worker_thread+0x1a1/0x310
kthread+0xfc/0x240
ret_from_fork+0x243/0x280
ret_from_fork_asm+0x1a/0x30
</TASK>
On fuse this is problematic because there are paths that may cause the
flusher thread to block (eg if systemd freezes the user session cgroups
first, which freezes the fuse daemon, before invoking the kernel
suspend. The kernel suspend triggers ->write_node() which on fuse issues
a synchronous setattr request, which cannot be processed since the
daemon is frozen. Or if the daemon is buggy and cannot properly complete
writeback, initiating writeback on a dirty folio already under writeback
leads to writeback_get_folio() -> folio_prepare_writeback() ->
unconditional wait on writeback to finish, which will cause a hang).
This commit restores fuse to its prior behavior before tmp folios were
removed, where sync was essentially a no-op.
[1] https://lore.kernel.org/linux-fsdevel/CAJnrk1a-asuvfrbKXbEwwDSctvemF+6zfhdnuzO65Pt8HsFSRw@mail.gmail.com/T/#m632c4648e9cafc4239299887109ebd880ac6c5c1 |
| In the Linux kernel, the following vulnerability has been resolved:
mm/huge_memory: fix folio isn't locked in softleaf_to_folio()
On arm64 server, we found folio that get from migration entry isn't locked
in softleaf_to_folio(). This issue triggers when mTHP splitting and
zap_nonpresent_ptes() races, and the root cause is lack of memory barrier
in softleaf_to_folio(). The race is as follows:
CPU0 CPU1
deferred_split_scan() zap_nonpresent_ptes()
lock folio
split_folio()
unmap_folio()
change ptes to migration entries
__split_folio_to_order() softleaf_to_folio()
set flags(including PG_locked) for tail pages folio = pfn_folio(softleaf_to_pfn(entry))
smp_wmb() VM_WARN_ON_ONCE(!folio_test_locked(folio))
prep_compound_page() for tail pages
In __split_folio_to_order(), smp_wmb() guarantees page flags of tail pages
are visible before the tail page becomes non-compound. smp_wmb() should
be paired with smp_rmb() in softleaf_to_folio(), which is missed. As a
result, if zap_nonpresent_ptes() accesses migration entry that stores tail
pfn, softleaf_to_folio() may see the updated compound_head of tail page
before page->flags.
This issue will trigger VM_WARN_ON_ONCE() in pfn_swap_entry_folio()
because of the race between folio split and zap_nonpresent_ptes()
leading to a folio incorrectly undergoing modification without a folio
lock being held.
This is a BUG_ON() before commit 93976a20345b ("mm: eliminate further
swapops predicates"), which in merged in v6.19-rc1.
To fix it, add missing smp_rmb() if the softleaf entry is migration entry
in softleaf_to_folio() and softleaf_to_page().
[tujinjiang@huawei.com: update function name and comments] |
| In the Linux kernel, the following vulnerability has been resolved:
xfs: close crash window in attr dabtree inactivation
When inactivating an inode with node-format extended attributes,
xfs_attr3_node_inactive() invalidates all child leaf/node blocks via
xfs_trans_binval(), but intentionally does not remove the corresponding
entries from their parent node blocks. The implicit assumption is that
xfs_attr_inactive() will truncate the entire attr fork to zero extents
afterwards, so log recovery will never reach the root node and follow
those stale pointers.
However, if a log shutdown occurs after the leaf/node block cancellations
commit but before the attr bmap truncation commits, this assumption
breaks. Recovery replays the attr bmap intact (the inode still has
attr fork extents), but suppresses replay of all cancelled leaf/node
blocks, maybe leaving them as stale data on disk. On the next mount,
xlog_recover_process_iunlinks() retries inactivation and attempts to
read the root node via the attr bmap. If the root node was not replayed,
reading the unreplayed root block triggers a metadata verification
failure immediately; if it was replayed, following its child pointers
to unreplayed child blocks triggers the same failure:
XFS (pmem0): Metadata corruption detected at
xfs_da3_node_read_verify+0x53/0x220, xfs_da3_node block 0x78
XFS (pmem0): Unmount and run xfs_repair
XFS (pmem0): First 128 bytes of corrupted metadata buffer:
00000000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00000010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00000020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00000030: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00000040: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00000050: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00000060: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00000070: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
XFS (pmem0): metadata I/O error in "xfs_da_read_buf+0x104/0x190" at daddr 0x78 len 8 error 117
Fix this in two places:
In xfs_attr3_node_inactive(), after calling xfs_trans_binval() on a
child block, immediately remove the entry that references it from the
parent node in the same transaction. This eliminates the window where
the parent holds a pointer to a cancelled block. Once all children are
removed, the now-empty root node is converted to a leaf block within the
same transaction. This node-to-leaf conversion is necessary for crash
safety. If the system shutdown after the empty node is written to the
log but before the second-phase bmap truncation commits, log recovery
will attempt to verify the root block on disk. xfs_da3_node_verify()
does not permit a node block with count == 0; such a block will fail
verification and trigger a metadata corruption shutdown. on the other
hand, leaf blocks are allowed to have this transient state.
In xfs_attr_inactive(), split the attr fork truncation into two explicit
phases. First, truncate all extents beyond the root block (the child
extents whose parent references have already been removed above).
Second, invalidate the root block and truncate the attr bmap to zero in
a single transaction. The two operations in the second phase must be
atomic: as long as the attr bmap has any non-zero length, recovery can
follow it to the root block, so the root block invalidation must commit
together with the bmap-to-zero truncation. |
