| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdkfd: fix a vulnerability of integer overflow in kfd debugger
get_queue_ids() computes array_size = num_queues * sizeof(uint32_t),
which could overflow on 32-bit size_t build. using array_size()
instead, it saturates to SIZE_MAX on overflow.
(cherry picked from commit 2d57a0475f085c08b49312dfd8edcb461845f285) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: fix lock leak on ENOMEM in AMDGPU_GEM_OP_GET_MAPPING_INFO
The AMDGPU_GEM_OP_GET_MAPPING_INFO branch of amdgpu_gem_op_ioctl()
holds three cleanup-tracked resources before calling kvcalloc():
the drm_gem_object reference from drm_gem_object_lookup(), the
drm_exec lock on the looked-up GEM via drm_exec_lock_obj(), and
the drm_exec lock on the per-process VM root page directory via
amdgpu_vm_lock_pd(). All three are released by the out_exec
label that every other error path in this function jumps to.
The kvcalloc() failure path returns -ENOMEM directly, skipping
out_exec and leaking all three.
The leaked per-process VM root PD dma_resv lock is the
load-bearing leak: any subsequent operation on the same VM
(further GEM ops, command-submission, eviction, TTM shrinker
callbacks) blocks on the held lock. DRM_IOCTL_AMDGPU_GEM_OP is
DRM_AUTH | DRM_RENDER_ALLOW, so this is an unprivileged-local
denial of service against the caller's GPU context, reachable
by any process with /dev/dri/renderD* access.
Route the failure through out_exec so drm_exec_fini() and
drm_gem_object_put() run.
Reproduced on stock 7.0.0-10, Ryzen 7 5700U / Radeon Vega
(Lucienne): the failing ioctl returns -ENOMEM and a second
GET_MAPPING_INFO on the same fd then blocks in
drm_exec_lock_obj() on the leaked dma_resv. SIGKILL on the
caller does not reap the task; the fd-release path during
process exit goes through amdgpu_gem_object_close() ->
drm_exec_prepare_obj() on the same lock, leaving the task in D
state until the box is rebooted. The patched kernel was not
rebuilt and re-tested on this hardware; the fix is mechanical.
Tested on a single Lucienne / Vega box only.
Ziyi Guo posted an independent INT_MAX-bound check for
args->num_entries in the same branch [1]; the two patches are
complementary and can land in either order.
(cherry picked from commit b69d3256d79de15f54c322986ff4da68f1d65b0a) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: fix amdgpu_hmm_range_get_pages
The notifier sequence must only be read once or otherwise we could work
with invalid pages.
While at it also fix the coding style, e.g. drop the pre-initialized
return value and use the common define for 2G range.
(cherry picked from commit c08972f555945cda57b0adb72272a37910153390) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: check num_entries in GEM_OP GET_MAPPING_INFO
kvcalloc(args->num_entries, sizeof(*vm_entries), GFP_KERNEL) at
amdgpu_gem.c:1050 uses the user-supplied num_entries directly without
any upper bounds check. Since num_entries is a __u32 and
sizeof(drm_amdgpu_gem_vm_entry) is 32 bytes, a large num_entries
produces an allocation exceeding INT_MAX, triggering
WARNING in __kvmalloc_node_noprof(), causing a kernel WARNING,
TAINT_WARN, and panic on CONFIG_PANIC_ON_WARN=y systems.
Add a size bounds check before we invoke the kvzalloc() to
reject oversized num_entries early with -EINVAL.
(cherry picked from commit 1fe7bf5457f6efd7be60b17e23163ba54341d73d) |
| In the Linux kernel, the following vulnerability has been resolved:
serial: dz: Convert to use a platform device
Prevent a crash from happening as the first serial port is initialised:
Console: switching to colour frame buffer device 160x64
tgafb: SFB+ detected, rev=0x02
fb0: Digital ZLX-E1 frame buffer device at 0x1e000000
DECstation DZ serial driver version 1.04
CPU 0 Unable to handle kernel paging request at virtual address 000000bc, epc == 8048b3a4, ra == 80470a78
Oops[#1]:
CPU: 0 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.19.0-dirty #35 NONE
$ 0 : 00000000 1000ac00 00000004 804707ac
$ 4 : 00000000 80e20850 80e20858 81000030
$ 8 : 00000000 8072c81c 00000008 fefefeff
$12 : 6c616972 00000006 80c5917f 69726420
$16 : 80e20800 00000000 808f8968 80e20800
$20 : 00000000 807f5a90 808b0094 808d3bc8
$24 : 00000018 80479030
$28 : 80c2e000 80c2fd70 00000069 80470a78
Hi : 00000004
Lo : 00000000
epc : 8048b3a4 __dev_fwnode+0x0/0xc
ra : 80470a78 serial_base_ctrl_add+0xa0/0x168
Status: 1000ac04 IEp
Cause : 30000008 (ExcCode 02)
BadVA : 000000bc
PrId : 00000220 (R3000)
Modules linked in:
Process swapper/0 (pid: 1, threadinfo=(ptrval), task=(ptrval), tls=00000000)
Stack : 00400044 00400040 8046f4cc 00000000 808a6148 808a0000 808f8968 8086983c
808e0000 8046fc84 1000ac01 00000028 80e20700 802ba3f8 80e20700 80d34a94
80c1b900 80e20700 80e20700 80e20700 80e20700 80444650 00000000 00000000
00000000 807f5a90 808b0094 80447080 00400040 808e0000 80d34a94 808a6148
80d34a94 00000004 80e20700 00000000 8076974c 80469810 80c2fe3c 1000ac01
...
Call Trace:
[<8048b3a4>] __dev_fwnode+0x0/0xc
[<80470a78>] serial_base_ctrl_add+0xa0/0x168
[<8046fc84>] serial_core_register_port+0x1c8/0x974
[<808c6af0>] dz_init+0x74/0xc8
[<800470e0>] do_one_initcall+0x44/0x2d4
[<808b111c>] kernel_init_freeable+0x258/0x308
[<8072e434>] kernel_init+0x20/0x114
[<80049cd0>] ret_from_kernel_thread+0x14/0x1c
Code: 27bd0018 03e00008 2402ffea <8c8200bc> 03e00008 00000000 27bdffc0 afbe0038 afb30024
---[ end trace 0000000000000000 ]---
-- where a pointer is dereferenced that has been derived from a null
pointer to the port's parent device.
Since no device is available with legacy probing and it's not anymore a
preferable way to discover devices anyway, switch the driver to using a
platform device and use it as the port's parent device. Update resource
handling accordingly and only request the actual span of addresses used
within the slot, which will have had its resource already requested by
generic platform device code.
Use platform_driver_probe() not just because the DZ device is fixed with
solder on board and not straightforward to remove, but foremost because
the associated TTY's major device number is the same as used by the zs
driver and the first driver to claim it will prevent the other one from
using it. Either one DZ device or some SCC devices will be present in a
given system but never both at a time, and therefore we want the major
device number to be claimed by the first driver to actually successfully
bind to its device and platform_driver_probe() is a way to fulfil that.
An unfortunate consequence of the switch to a platform device is we now
hand the console over from the bootconsole much later in the bootstrap.
The firmware console handler appears good enough though to work so late
and in particular with interrupts enabled.
Conversely only starting the console port so late lets the reset code
fully utilise our delay handlers, so switch from udelay() to fsleep()
for transmitter draining so as to avoid busy-waiting for an excessive
amount of time. |
| In the Linux kernel, the following vulnerability has been resolved:
serial: zs: Convert to use a platform device
Prevent a crash from happening as the first serial port is initialised:
Console: switching to mono frame buffer device 160x64
fb0: PMAG-AA frame buffer device at tc0
DECstation Z85C30 serial driver version 0.10
CPU 0 Unable to handle kernel paging request at virtual address 0000002c, epc == 803ab00c, ra == 803aafe0
Oops[#1]:
CPU: 0 PID: 1 Comm: swapper Not tainted 6.4.0-rc3-00031-g84a9582fd203-dirty #57
$ 0 : 00000000 10012c00 803aaeb0 00000000
$ 4 : 80e12f60 80e12f50 80e12f58 81000030
$ 8 : 00000000 805ff37c 00000000 33433538
$12 : 65732030 00000006 80c2915d 6c616972
$16 : 80e12f00 807b7630 00000000 00000000
$20 : 00000004 00000348 000001a0 807623b8
$24 : 00000018 00000000
$28 : 80c24000 80c25d60 8078b148 803aafe0
Hi : 00000000
Lo : 00000000
epc : 803ab00c serial_base_ctrl_add+0x78/0xf4
ra : 803aafe0 serial_base_ctrl_add+0x4c/0xf4
Status: 10012c03 KERNEL EXL IE
Cause : 00000008 (ExcCode 02)
BadVA : 0000002c
PrId : 00000440 (R4400SC)
Modules linked in:
Process swapper (pid: 1, threadinfo=(ptrval), task=(ptrval), tls=00000000)
Stack : 80760000 00000cc0 00400044 00400040 803aa02c 80d61ab8 00000000 807b7630
80760000 807623b8 807b7628 803aa644 80386998 00000000 80e17780 80220f68
80e17780 80d61ab8 80c17d80 80e17780 80e17780 8063c798 80e17780 80383fa0
00000010 80e17780 00000000 80386998 807a0000 00000000 00400040 8038f848
807623b8 80d61ab8 00000004 80e17780 00000000 803a68e4 80c25e2c 803bb884
...
Call Trace:
[<803ab00c>] serial_base_ctrl_add+0x78/0xf4
[<803aa644>] serial_core_register_port+0x174/0x69c
[<8077e9ac>] zs_init+0xc8/0xfc
[<800404d4>] do_one_initcall+0x40/0x2ac
[<8076cecc>] kernel_init_freeable+0x1e4/0x270
[<80605bec>] kernel_init+0x20/0x108
[<800431e8>] ret_from_kernel_thread+0x14/0x1c
Code: 2442aeb0 ae120024 ae0200d0 <8c67002c> 50e00001 8c670000 3c06806e 3c05806e afb30010
---[ end trace 0000000000000000 ]---
(report at the offending commit) -- where a pointer is dereferenced that
has been derived from a null pointer to the port's parent device.
Since no device is available with legacy probing and it's not anymore a
preferable way to discover devices anyway, switch the driver to using a
platform device and use it as the port's parent device. Update resource
handling accordingly and only request the actual span of addresses used
within the slot, which will have had its resource already requested by
generic platform device code.
Use platform_driver_probe() not just because SCC devices are fixed with
solder on board and not straightforward to remove, but foremost because
the associated TTY's major device number is the same as used by the dz
driver and the first driver to claim it will prevent the other one from
using it. Either one DZ device or some SCC devices will be present in a
given system but never both at a time, and therefore we want the major
device number to be claimed by the first driver to actually successfully
bind to its device and platform_driver_probe() is a way to fulfil that.
An unfortunate consequence of the switch to a platform device is we now
hand the console over from the bootconsole much later in the bootstrap.
The firmware console handler appears good enough though to work so late
and in particular with interrupts enabled.
Since there is one way only remaining to reach zs_reset() now, remove
the port initialisation marker as no longer needed and go through the
channel reset unconditionally. |
| In the Linux kernel, the following vulnerability has been resolved:
arm64: tlb: Flush walk cache when unsharing PMD tables
When huge_pmd_unshare() is called to unshare a PMD table, the
tlb_unshare_pmd_ptdesc() function sets tlb->unshared_tables=true
but the aarch64 tlb_flush() only checked tlb->freed_tables to
determine whether to use TLBF_NONE (vae1is, invalidates walk
cache) or TLBF_NOWALKCACHE (vale1is, leaf-only).
This caused the stale PMD page table entry to remain in the walk cache
after unshare, potentially leading to incorrect page table walks.
Fix by including unshared_tables in the check, so that when
unsharing tables, TLBF_NONE is used and the walk cache is properly
invalidated.
Here is the detailed distinction between vae1is and vale1is:
| Instruction Combination | Actual Invalidation Scope |
| ------------------------ | --------------------------------------------------|
| `VAE1IS` + TTL=`0` | All entries at all levels (full invalidation) |
| `VAE1IS` + TTL=`2` (L2) | Non-leaf at Level 0/1 + leaf at Level 2 |
| `VALE1IS` + TTL=`0` | Leaf entries at all levels (non-leaf not cleared) |
| `VALE1IS` + TTL=`2` (L2) | Leaf entry at Level 2 only | |
| In the Linux kernel, the following vulnerability has been resolved:
net: mctp: usb: fix race between urb completion and rx_retry cancellation
It's possible that sequencing between setting ->stopped and cancelling
the rx_retry work (in ndo_stop) could leave us with an urb queued:
T1: ndo_stop T2: rx_retry_work
------------ ----------------
LD: ->stopped => false
ST: ->stopped <= true
usb_kill_urb()
mctp_usb_rx_queue()
usb_submit_urb()
cancel_delayed_work_sync()
That urb completion can then re-schedule rx_retry_work.
Strenghen the sequencing between the stop (preventing another requeue)
and the cancel by updating both atomically under a new rx lock. After
setting ->rx_stopped, and cancelling pending work, we know that the
requeue cannot occur, so all that's left is killing any pending urb. |
| In the Linux kernel, the following vulnerability has been resolved:
accel/amdxdna: Fix mm_struct reference leak in aie2_populate_range()
aie2_populate_range() jumps back to the again label without calling
mmput(mm), leaking a reference to the mm_struct.
Add the missing mmput() before jumping to again. |
| In the Linux kernel, the following vulnerability has been resolved:
esp: fix page frag reference leak on skb_to_sgvec failure
In esp_output_tail(), when esp->inplace is false, the old skb page frags
are replaced with a new page from the xfrm page_frag cache. The source
scatterlist (sg) is built from the old frags before the replacement, and
esp_ssg_unref() is responsible for releasing the old page references
after the crypto operation completes.
However, if the second skb_to_sgvec() call (which builds the destination
scatterlist from the new page) fails, the code jumps to error_free which
only calls kfree(tmp). The old page frag references captured in the
source scatterlist are never released:
1. sg[] is built from old frags via skb_to_sgvec() (no extra get_page)
2. nr_frags is set to 1 and frag[0] is replaced with the new page
3. Second skb_to_sgvec() fails -> goto error_free
4. kfree(tmp) frees the sg[] memory but old frags are not unref'd
5. kfree_skb() only releases frag[0] (the new page), not the old ones
Fix this by adding a bool parameter to esp_ssg_unref() that, when true,
unconditionally unrefs the source scatterlist frags without checking
req->src and req->dst, since those fields are not yet initialized by
aead_request_set_crypt() at the point of the error. Existing callers
pass false to preserve the original behavior.
The same issue exists in both esp4 and esp6 as the code is identical. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: ISO: Fix data-race on iso_pi fields in hci_get_route calls
iso_connect_bis(), iso_connect_cis(), iso_listen_bis(), and
iso_conn_big_sync() call hci_get_route() using iso_pi(sk)->dst,
iso_pi(sk)->src, and iso_pi(sk)->src_type without holding lock_sock().
These fields may be modified concurrently by connect() or setsockopt()
on the same socket, resulting in data-races reported by KCSAN.
Fix this by snapshotting the required fields under lock_sock() before
calling hci_get_route().
BUG: KCSAN: data-race in memcmp+0x45/0xb0
race at unknown origin, with read to 0xffff8880122135cf of 1 bytes
by task 333 on cpu 1:
memcmp+0x45/0xb0
hci_get_route+0x27e/0x490
iso_connect_cis+0x4c/0xa10
iso_sock_connect+0x60e/0xb30
__sys_connect_file+0xbd/0xe0
__sys_connect+0xe0/0x110
__x64_sys_connect+0x40/0x50
x64_sys_call+0xcad/0x1c60
do_syscall_64+0x133/0x590
entry_SYSCALL_64_after_hwframe+0x77/0x7f |
| In the Linux kernel, the following vulnerability has been resolved:
ieee802154: 6lowpan: only accept IPv6 packets in lowpan_xmit()
The aoe driver (or similar) generates a non-IPv6 packet
(e.g., ETH_P_AOE) and queues it for transmission via dev_queue_xmit()
on a 6LoWPAN interface (configured by the user or test case).
Since the packet is not IPv6, the 6LoWPAN header_ops->create function
(lowpan_header_create or header_create) returns early without initializing
the lowpan_addr_info structure in the skb headroom.
In the transmit function (lowpan_xmit), the driver calls lowpan_header
(or setup_header) which unconditionally copies and uses the lowpan_addr_info
from the headroom, which contains uninitialized data.
Fix this by dropping non IPv6 packets.
A similar fix is needed in net/bluetooth/6lowpan.c bt_xmit(). |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: limit injected antenna index in ieee80211_parse_tx_radiotap
When parsing the radiotap header of an injected frame,
ieee80211_parse_tx_radiotap() uses the IEEE80211_RADIOTAP_ANTENNA value
directly as a shift count:
info->control.antennas |= BIT(*iterator.this_arg);
*iterator.this_arg is an 8-bit value taken straight from the frame
supplied by userspace, so BIT() can be asked to shift by up to 255. That
is undefined behaviour on the unsigned long and is reported by UBSAN:
UBSAN: shift-out-of-bounds in net/mac80211/tx.c:2174:30
shift exponent 235 is too large for 64-bit type 'unsigned long'
Call Trace:
ieee80211_parse_tx_radiotap+0xadb/0x1950 net/mac80211/tx.c:2174
ieee80211_monitor_start_xmit+0xb1f/0x1250 net/mac80211/tx.c:2451
...
packet_sendmsg+0x3eb6/0x50f0 net/packet/af_packet.c:3109
info->control.antennas is a 2-bit bitmap (u8 antennas:2), so only antenna
indices 0 and 1 can ever be represented. Ignore any larger value instead
of shifting out of bounds. |
| In the Linux kernel, the following vulnerability has been resolved:
net: garp: fix unsigned integer underflow in garp_pdu_parse_attr
The receive-side GARP attribute parser computes dlen with reversed
operands:
dlen = sizeof(*ga) - ga->len;
ga->len is the on-wire attribute length and includes the GARP attribute
header. For normal attributes with data, ga->len is larger than
sizeof(*ga), so the subtraction underflows in unsigned arithmetic.
The resulting value is later passed to garp_attr_lookup(), whose length
argument is u8. After truncation, the parsed data length usually no
longer matches the length stored for locally registered attributes, so
received Join/Leave events are ignored. This breaks the GARP receive path
for common attributes, such as GVRP VLAN registration attributes.
Compute the data length as the attribute length minus the header length. |
| In the Linux kernel, the following vulnerability has been resolved:
mptcp: close TOCTOU race while computing rcv_wnd
The MPTCP output path access locklessly the MPTCP-level ack_seq
in multiple times, using possibly different values for the data_ack
in the DSS option and to compute the announced rcv wnd for the same
packet.
Refactor the cote to avoid inconsistencies which may confuse the
peer. Also ensure that the MPTCP level rcv wnd is updated only when
the egress packet actually contains a DSS ack. |
| Impact: fast-uri versions from 2.3.1 through 4.1.0 (including the 3.x line up to 3.1.3 and the 2.x line up to 2.4.2) do not treat a literal backslash character (U+005C) as an authority delimiter. Node's native WHATWG URL parser, used by fetch, undici, and Node's http and https clients, normalizes the backslash to a forward slash for special schemes such as http, https, ws, wss, ftp, and file. As a result, the two parsers extract different hosts from the same input string. Applications that use fast-uri to enforce host-based policy such as allowlists, denylists, loopback or SSRF filtering, redirect validation, or outbound proxy routing before passing the same URL into Node's URL or fetch consumers can be steered to an unintended destination, including cloud metadata endpoints, loopback, or internal hosts.
Patches: upgrade to fast-uri 4.1.1, 3.1.4, or 2.4.3.
Workarounds: none. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: Clear wcid pointer in mt7996_mac_sta_deinit_link()
Clear WCID pointer removing the sta link in mt7996_mac_sta_deinit_link
routine. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Drop task_to_inode and inet_conn_established from lsm sleepable hooks
bpf_lsm_task_to_inode() is called under rcu_read_lock() and
bpf_lsm_inet_conn_established() is called from softirq context, so
neither hook can be used by sleepable LSM programs. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Propagate error from visit_tailcall_insn
Commit e40f5a6bf88a ("bpf: correct stack liveness for tail calls") added
visit_tailcall_insn() but did not check its return value. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/gpusvm: Fix unbalanced unlock in drm_gpusvm_scan_mm()
There is a unbalanced lock/unlock to gpusvm notifier lock:
[ 931.045868] =====================================
[ 931.046509] WARNING: bad unlock balance detected!
[ 931.047149] 6.19.0-rc6+xe-**************** #9 Tainted: G U
[ 931.048150] -------------------------------------
[ 931.048790] kworker/u5:0/51 is trying to release lock (&gpusvm->notifier_lock) at:
[ 931.049801] [<ffffffffa090c0d8>] drm_gpusvm_scan_mm+0x188/0x460 [drm_gpusvm_helper]
[ 931.050802] but there are no more locks to release!
[ 931.051463]
The drm_gpusvm_notifier_unlock() sits under err_free label and the
first jump to err_free is just before calling the
drm_gpusvm_notifier_lock() causing unbalanced unlock. |
