| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtl8xxxu: fix slab-out-of-bounds in rtl8xxxu_sta_add
The driver does not set hw->sta_data_size, which causes mac80211 to
allocate insufficient space for driver private station data in
__sta_info_alloc(). When rtl8xxxu_sta_add() accesses members of
struct rtl8xxxu_sta_info through sta->drv_priv, this results in a
slab-out-of-bounds write.
KASAN report on RISC-V (VisionFive 2) with RTL8192EU adapter:
BUG: KASAN: slab-out-of-bounds in rtl8xxxu_sta_add+0x31c/0x346
Write of size 8 at addr ffffffd6d3e9ae88 by task kworker/u16:0/12
Set hw->sta_data_size to sizeof(struct rtl8xxxu_sta_info) during
probe, similar to how hw->vif_data_size is configured. This ensures
mac80211 allocates sufficient space for the driver's per-station
private data.
Tested on StarFive VisionFive 2 v1.2A board. |
| In the Linux kernel, the following vulnerability has been resolved:
net: phy: allow MDIO bus PM ops to start/stop state machine for phylink-controlled PHY
DSA has 2 kinds of drivers:
1. Those who call dsa_switch_suspend() and dsa_switch_resume() from
their device PM ops: qca8k-8xxx, bcm_sf2, microchip ksz
2. Those who don't: all others. The above methods should be optional.
For type 1, dsa_switch_suspend() calls dsa_user_suspend() -> phylink_stop(),
and dsa_switch_resume() calls dsa_user_resume() -> phylink_start().
These seem good candidates for setting mac_managed_pm = true because
that is essentially its definition [1], but that does not seem to be the
biggest problem for now, and is not what this change focuses on.
Talking strictly about the 2nd category of DSA drivers here (which
do not have MAC managed PM, meaning that for their attached PHYs,
mdio_bus_phy_suspend() and mdio_bus_phy_resume() should run in full),
I have noticed that the following warning from mdio_bus_phy_resume() is
triggered:
WARN_ON(phydev->state != PHY_HALTED && phydev->state != PHY_READY &&
phydev->state != PHY_UP);
because the PHY state machine is running.
It's running as a result of a previous dsa_user_open() -> ... ->
phylink_start() -> phy_start() having been initiated by the user.
The previous mdio_bus_phy_suspend() was supposed to have called
phy_stop_machine(), but it didn't. So this is why the PHY is in state
PHY_NOLINK by the time mdio_bus_phy_resume() runs.
mdio_bus_phy_suspend() did not call phy_stop_machine() because for
phylink, the phydev->adjust_link function pointer is NULL. This seems a
technicality introduced by commit fddd91016d16 ("phylib: fix PAL state
machine restart on resume"). That commit was written before phylink
existed, and was intended to avoid crashing with consumer drivers which
don't use the PHY state machine - phylink always does, when using a PHY.
But phylink itself has historically not been developed with
suspend/resume in mind, and apparently not tested too much in that
scenario, allowing this bug to exist unnoticed for so long. Plus, prior
to the WARN_ON(), it would have likely been invisible.
This issue is not in fact restricted to type 2 DSA drivers (according to
the above ad-hoc classification), but can be extrapolated to any MAC
driver with phylink and MDIO-bus-managed PHY PM ops. DSA is just where
the issue was reported. Assuming mac_managed_pm is set correctly, a
quick search indicates the following other drivers might be affected:
$ grep -Zlr PHYLINK_NETDEV drivers/ | xargs -0 grep -L mac_managed_pm
drivers/net/ethernet/atheros/ag71xx.c
drivers/net/ethernet/microchip/sparx5/sparx5_main.c
drivers/net/ethernet/microchip/lan966x/lan966x_main.c
drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.c
drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c
drivers/net/ethernet/freescale/dpaa/dpaa_eth.c
drivers/net/ethernet/freescale/ucc_geth.c
drivers/net/ethernet/freescale/enetc/enetc_pf_common.c
drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
drivers/net/ethernet/marvell/mvneta.c
drivers/net/ethernet/marvell/prestera/prestera_main.c
drivers/net/ethernet/mediatek/mtk_eth_soc.c
drivers/net/ethernet/altera/altera_tse_main.c
drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
drivers/net/ethernet/meta/fbnic/fbnic_phylink.c
drivers/net/ethernet/tehuti/tn40_phy.c
drivers/net/ethernet/mscc/ocelot_net.c
Make the existing conditions dependent on the PHY device having a
phydev->phy_link_change() implementation equal to the default
phy_link_change() provided by phylib. Otherwise, we implicitly know that
the phydev has the phylink-provided phylink_phy_change() callback, and
when phylink is used, the PHY state machine always needs to be stopped/
started on the suspend/resume path. The code is structured as such that
if phydev->phy_link_change() is absent, it is a matter of time until the
kernel will crash - no need to further complicate the test.
Thus, for the situation where the PM is not managed b
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
gfs2: Fix unlikely race in gdlm_put_lock
In gdlm_put_lock(), there is a small window of time in which the
DFL_UNMOUNT flag has been set but the lockspace hasn't been released,
yet. In that window, dlm may still call gdlm_ast() and gdlm_bast().
To prevent it from dereferencing freed glock objects, only free the
glock if the lockspace has actually been released. |
| In the Linux kernel, the following vulnerability has been resolved:
nvme: fix admin request_queue lifetime
The namespaces can access the controller's admin request_queue, and
stale references on the namespaces may exist after tearing down the
controller. Ensure the admin request_queue is active by moving the
controller's 'put' to after all controller references have been released
to ensure no one is can access the request_queue. This fixes a reported
use-after-free bug:
BUG: KASAN: slab-use-after-free in blk_queue_enter+0x41c/0x4a0
Read of size 8 at addr ffff88c0a53819f8 by task nvme/3287
CPU: 67 UID: 0 PID: 3287 Comm: nvme Tainted: G E 6.13.2-ga1582f1a031e #15
Tainted: [E]=UNSIGNED_MODULE
Hardware name: Jabil /EGS 2S MB1, BIOS 1.00 06/18/2025
Call Trace:
<TASK>
dump_stack_lvl+0x4f/0x60
print_report+0xc4/0x620
? _raw_spin_lock_irqsave+0x70/0xb0
? _raw_read_unlock_irqrestore+0x30/0x30
? blk_queue_enter+0x41c/0x4a0
kasan_report+0xab/0xe0
? blk_queue_enter+0x41c/0x4a0
blk_queue_enter+0x41c/0x4a0
? __irq_work_queue_local+0x75/0x1d0
? blk_queue_start_drain+0x70/0x70
? irq_work_queue+0x18/0x20
? vprintk_emit.part.0+0x1cc/0x350
? wake_up_klogd_work_func+0x60/0x60
blk_mq_alloc_request+0x2b7/0x6b0
? __blk_mq_alloc_requests+0x1060/0x1060
? __switch_to+0x5b7/0x1060
nvme_submit_user_cmd+0xa9/0x330
nvme_user_cmd.isra.0+0x240/0x3f0
? force_sigsegv+0xe0/0xe0
? nvme_user_cmd64+0x400/0x400
? vfs_fileattr_set+0x9b0/0x9b0
? cgroup_update_frozen_flag+0x24/0x1c0
? cgroup_leave_frozen+0x204/0x330
? nvme_ioctl+0x7c/0x2c0
blkdev_ioctl+0x1a8/0x4d0
? blkdev_common_ioctl+0x1930/0x1930
? fdget+0x54/0x380
__x64_sys_ioctl+0x129/0x190
do_syscall_64+0x5b/0x160
entry_SYSCALL_64_after_hwframe+0x4b/0x53
RIP: 0033:0x7f765f703b0b
Code: ff ff ff 85 c0 79 9b 49 c7 c4 ff ff ff ff 5b 5d 4c 89 e0 41 5c c3 66 0f 1f 84 00 00 00 00 00 f3 0f 1e fa b8 10 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d dd 52 0f 00 f7 d8 64 89 01 48
RSP: 002b:00007ffe2cefe808 EFLAGS: 00000202 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 00007ffe2cefe860 RCX: 00007f765f703b0b
RDX: 00007ffe2cefe860 RSI: 00000000c0484e41 RDI: 0000000000000003
RBP: 0000000000000000 R08: 0000000000000003 R09: 0000000000000000
R10: 00007f765f611d50 R11: 0000000000000202 R12: 0000000000000003
R13: 00000000c0484e41 R14: 0000000000000001 R15: 00007ffe2cefea60
</TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: Fix refcount leak when invalid session is found on session lookup
When a session is found but its state is not SMB2_SESSION_VALID, It
indicates that no valid session was found, but it is missing to decrement
the reference count acquired by the session lookup, which results in
a reference count leak. This patch fixes the issue by explicitly calling
ksmbd_user_session_put to release the reference to the session. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw88: Fix alignment fault in rtw_core_enable_beacon()
rtw_core_enable_beacon() reads 4 bytes from an address that is not a
multiple of 4. This results in a crash on some systems.
Do 1 byte reads/writes instead.
Unable to handle kernel paging request at virtual address ffff8000827e0522
Mem abort info:
ESR = 0x0000000096000021
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x21: alignment fault
Data abort info:
ISV = 0, ISS = 0x00000021, ISS2 = 0x00000000
CM = 0, WnR = 0, TnD = 0, TagAccess = 0
GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0
swapper pgtable: 4k pages, 48-bit VAs, pgdp=0000000005492000
[ffff8000827e0522] pgd=0000000000000000, p4d=10000001021d9403, pud=10000001021da403, pmd=100000011061c403, pte=00780000f3200f13
Internal error: Oops: 0000000096000021 [#1] SMP
Modules linked in: [...] rtw88_8822ce rtw88_8822c rtw88_pci rtw88_core [...]
CPU: 0 UID: 0 PID: 73 Comm: kworker/u32:2 Tainted: G W 6.17.9 #1-NixOS VOLUNTARY
Tainted: [W]=WARN
Hardware name: FriendlyElec NanoPC-T6 LTS (DT)
Workqueue: phy0 rtw_c2h_work [rtw88_core]
pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : rtw_pci_read32+0x18/0x40 [rtw88_pci]
lr : rtw_core_enable_beacon+0xe0/0x148 [rtw88_core]
sp : ffff800080cc3ca0
x29: ffff800080cc3ca0 x28: ffff0001031fc240 x27: ffff000102100828
x26: ffffd2cb7c9b4088 x25: ffff0001031fc2c0 x24: ffff000112fdef00
x23: ffff000112fdef18 x22: ffff000111c29970 x21: 0000000000000001
x20: 0000000000000001 x19: ffff000111c22040 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000
x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000
x11: 0000000000000000 x10: 0000000000000000 x9 : ffffd2cb6507c090
x8 : 0000000000000000 x7 : 0000000000000000 x6 : 0000000000000000
x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000000000
x2 : 0000000000007f10 x1 : 0000000000000522 x0 : ffff8000827e0522
Call trace:
rtw_pci_read32+0x18/0x40 [rtw88_pci] (P)
rtw_hw_scan_chan_switch+0x124/0x1a8 [rtw88_core]
rtw_fw_c2h_cmd_handle+0x254/0x290 [rtw88_core]
rtw_c2h_work+0x50/0x98 [rtw88_core]
process_one_work+0x178/0x3f8
worker_thread+0x208/0x418
kthread+0x120/0x220
ret_from_fork+0x10/0x20
Code: d28fe202 8b020000 f9524400 8b214000 (b9400000)
---[ end trace 0000000000000000 ]--- |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: iaa - Fix out-of-bounds index in find_empty_iaa_compression_mode
The local variable 'i' is initialized with -EINVAL, but the for loop
immediately overwrites it and -EINVAL is never returned.
If no empty compression mode can be found, the function would return the
out-of-bounds index IAA_COMP_MODES_MAX, which would cause an invalid
array access in add_iaa_compression_mode().
Fix both issues by returning either a valid index or -EINVAL. |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: endpoint: Avoid creating sub-groups asynchronously
The asynchronous creation of sub-groups by a delayed work could lead to a
NULL pointer dereference when the driver directory is removed before the
work completes.
The crash can be easily reproduced with the following commands:
# cd /sys/kernel/config/pci_ep/functions/pci_epf_test
# for i in {1..20}; do mkdir test && rmdir test; done
BUG: kernel NULL pointer dereference, address: 0000000000000088
...
Call Trace:
configfs_register_group+0x3d/0x190
pci_epf_cfs_work+0x41/0x110
process_one_work+0x18f/0x350
worker_thread+0x25a/0x3a0
Fix this issue by using configfs_add_default_group() API which does not
have the deadlock problem as configfs_register_group() and does not require
the delayed work handler.
[mani: slightly reworded the description and added stable list] |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Forget ranges when refining tnum after JSET
Syzbot reported a kernel warning due to a range invariant violation on
the following BPF program.
0: call bpf_get_netns_cookie
1: if r0 == 0 goto <exit>
2: if r0 & Oxffffffff goto <exit>
The issue is on the path where we fall through both jumps.
That path is unreachable at runtime: after insn 1, we know r0 != 0, but
with the sign extension on the jset, we would only fallthrough insn 2
if r0 == 0. Unfortunately, is_branch_taken() isn't currently able to
figure this out, so the verifier walks all branches. The verifier then
refines the register bounds using the second condition and we end
up with inconsistent bounds on this unreachable path:
1: if r0 == 0 goto <exit>
r0: u64=[0x1, 0xffffffffffffffff] var_off=(0, 0xffffffffffffffff)
2: if r0 & 0xffffffff goto <exit>
r0 before reg_bounds_sync: u64=[0x1, 0xffffffffffffffff] var_off=(0, 0)
r0 after reg_bounds_sync: u64=[0x1, 0] var_off=(0, 0)
Improving the range refinement for JSET to cover all cases is tricky. We
also don't expect many users to rely on JSET given LLVM doesn't generate
those instructions. So instead of improving the range refinement for
JSETs, Eduard suggested we forget the ranges whenever we're narrowing
tnums after a JSET. This patch implements that approach. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: simple-card-utils: Don't use __free(device_node) at graph_util_parse_dai()
commit 419d1918105e ("ASoC: simple-card-utils: use __free(device_node) for
device node") uses __free(device_node) for dlc->of_node, but we need to
keep it while driver is in use.
Don't use __free(device_node) in graph_util_parse_dai(). |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix null pointer dereference error in generate_encryptionkey
If client send two session setups with krb5 authenticate to ksmbd,
null pointer dereference error in generate_encryptionkey could happen.
sess->Preauth_HashValue is set to NULL if session is valid.
So this patch skip generate encryption key if session is valid. |
| In the Linux kernel, the following vulnerability has been resolved:
media: uvcvideo: Mark invalid entities with id UVC_INVALID_ENTITY_ID
Per UVC 1.1+ specification 3.7.2, units and terminals must have a non-zero
unique ID.
```
Each Unit and Terminal within the video function is assigned a unique
identification number, the Unit ID (UID) or Terminal ID (TID), contained in
the bUnitID or bTerminalID field of the descriptor. The value 0x00 is
reserved for undefined ID,
```
If we add a new entity with id 0 or a duplicated ID, it will be marked
as UVC_INVALID_ENTITY_ID.
In a previous attempt commit 3dd075fe8ebb ("media: uvcvideo: Require
entities to have a non-zero unique ID"), we ignored all the invalid units,
this broke a lot of non-compatible cameras. Hopefully we are more lucky
this time.
This also prevents some syzkaller reproducers from triggering warnings due
to a chain of entities referring to themselves. In one particular case, an
Output Unit is connected to an Input Unit, both with the same ID of 1. But
when looking up for the source ID of the Output Unit, that same entity is
found instead of the input entity, which leads to such warnings.
In another case, a backward chain was considered finished as the source ID
was 0. Later on, that entity was found, but its pads were not valid.
Here is a sample stack trace for one of those cases.
[ 20.650953] usb 1-1: new high-speed USB device number 2 using dummy_hcd
[ 20.830206] usb 1-1: Using ep0 maxpacket: 8
[ 20.833501] usb 1-1: config 0 descriptor??
[ 21.038518] usb 1-1: string descriptor 0 read error: -71
[ 21.038893] usb 1-1: Found UVC 0.00 device <unnamed> (2833:0201)
[ 21.039299] uvcvideo 1-1:0.0: Entity type for entity Output 1 was not initialized!
[ 21.041583] uvcvideo 1-1:0.0: Entity type for entity Input 1 was not initialized!
[ 21.042218] ------------[ cut here ]------------
[ 21.042536] WARNING: CPU: 0 PID: 9 at drivers/media/mc/mc-entity.c:1147 media_create_pad_link+0x2c4/0x2e0
[ 21.043195] Modules linked in:
[ 21.043535] CPU: 0 UID: 0 PID: 9 Comm: kworker/0:1 Not tainted 6.11.0-rc7-00030-g3480e43aeccf #444
[ 21.044101] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.15.0-1 04/01/2014
[ 21.044639] Workqueue: usb_hub_wq hub_event
[ 21.045100] RIP: 0010:media_create_pad_link+0x2c4/0x2e0
[ 21.045508] Code: fe e8 20 01 00 00 b8 f4 ff ff ff 48 83 c4 30 5b 41 5c 41 5d 41 5e 41 5f 5d c3 cc cc cc cc 0f 0b eb e9 0f 0b eb 0a 0f 0b eb 06 <0f> 0b eb 02 0f 0b b8 ea ff ff ff eb d4 66 2e 0f 1f 84 00 00 00 00
[ 21.046801] RSP: 0018:ffffc9000004b318 EFLAGS: 00010246
[ 21.047227] RAX: ffff888004e5d458 RBX: 0000000000000000 RCX: ffffffff818fccf1
[ 21.047719] RDX: 000000000000007b RSI: 0000000000000000 RDI: ffff888004313290
[ 21.048241] RBP: ffff888004313290 R08: 0001ffffffffffff R09: 0000000000000000
[ 21.048701] R10: 0000000000000013 R11: 0001888004313290 R12: 0000000000000003
[ 21.049138] R13: ffff888004313080 R14: ffff888004313080 R15: 0000000000000000
[ 21.049648] FS: 0000000000000000(0000) GS:ffff88803ec00000(0000) knlGS:0000000000000000
[ 21.050271] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 21.050688] CR2: 0000592cc27635b0 CR3: 000000000431c000 CR4: 0000000000750ef0
[ 21.051136] PKRU: 55555554
[ 21.051331] Call Trace:
[ 21.051480] <TASK>
[ 21.051611] ? __warn+0xc4/0x210
[ 21.051861] ? media_create_pad_link+0x2c4/0x2e0
[ 21.052252] ? report_bug+0x11b/0x1a0
[ 21.052540] ? trace_hardirqs_on+0x31/0x40
[ 21.052901] ? handle_bug+0x3d/0x70
[ 21.053197] ? exc_invalid_op+0x1a/0x50
[ 21.053511] ? asm_exc_invalid_op+0x1a/0x20
[ 21.053924] ? media_create_pad_link+0x91/0x2e0
[ 21.054364] ? media_create_pad_link+0x2c4/0x2e0
[ 21.054834] ? media_create_pad_link+0x91/0x2e0
[ 21.055131] ? _raw_spin_unlock+0x1e/0x40
[ 21.055441] ? __v4l2_device_register_subdev+0x202/0x210
[ 21.055837] uvc_mc_register_entities+0x358/0x400
[ 21.056144] uvc_register_chains+0x1
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
fbcon: Set fb_display[i]->mode to NULL when the mode is released
Recently, we discovered the following issue through syzkaller:
BUG: KASAN: slab-use-after-free in fb_mode_is_equal+0x285/0x2f0
Read of size 4 at addr ff11000001b3c69c by task syz.xxx
...
Call Trace:
<TASK>
dump_stack_lvl+0xab/0xe0
print_address_description.constprop.0+0x2c/0x390
print_report+0xb9/0x280
kasan_report+0xb8/0xf0
fb_mode_is_equal+0x285/0x2f0
fbcon_mode_deleted+0x129/0x180
fb_set_var+0xe7f/0x11d0
do_fb_ioctl+0x6a0/0x750
fb_ioctl+0xe0/0x140
__x64_sys_ioctl+0x193/0x210
do_syscall_64+0x5f/0x9c0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
Based on experimentation and analysis, during framebuffer unregistration,
only the memory of fb_info->modelist is freed, without setting the
corresponding fb_display[i]->mode to NULL for the freed modes. This leads
to UAF issues during subsequent accesses. Here's an example of reproduction
steps:
1. With /dev/fb0 already registered in the system, load a kernel module
to register a new device /dev/fb1;
2. Set fb1's mode to the global fb_display[] array (via FBIOPUT_CON2FBMAP);
3. Switch console from fb to VGA (to allow normal rmmod of the ko);
4. Unload the kernel module, at this point fb1's modelist is freed, leaving
a wild pointer in fb_display[];
5. Trigger the bug via system calls through fb0 attempting to delete a mode
from fb0.
Add a check in do_unregister_framebuffer(): if the mode to be freed exists
in fb_display[], set the corresponding mode pointer to NULL. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8723bs: fix out-of-bounds read in rtw_get_ie() parser
The Information Element (IE) parser rtw_get_ie() trusted the length
byte of each IE without validating that the IE body (len bytes after
the 2-byte header) fits inside the remaining frame buffer. A malformed
frame can advertise an IE length larger than the available data, causing
the parser to increment its pointer beyond the buffer end. This results
in out-of-bounds reads or, depending on the pattern, an infinite loop.
Fix by validating that (offset + 2 + len) does not exceed the limit
before accepting the IE or advancing to the next element.
This prevents OOB reads and ensures the parser terminates safely on
malformed frames. |
| In the Linux kernel, the following vulnerability has been resolved:
net: mctp: Don't access ifa_index when missing
In mctp_dump_addrinfo, ifa_index can be used to filter interfaces, but
only when the struct ifaddrmsg is provided. Otherwise it will be
comparing to uninitialised memory - reproducible in the syzkaller case from
dhcpd, or busybox "ip addr show".
The kernel MCTP implementation has always filtered by ifa_index, so
existing userspace programs expecting to dump MCTP addresses must
already be passing a valid ifa_index value (either 0 or a real index).
BUG: KMSAN: uninit-value in mctp_dump_addrinfo+0x208/0xac0 net/mctp/device.c:128
mctp_dump_addrinfo+0x208/0xac0 net/mctp/device.c:128
rtnl_dump_all+0x3ec/0x5b0 net/core/rtnetlink.c:4380
rtnl_dumpit+0xd5/0x2f0 net/core/rtnetlink.c:6824
netlink_dump+0x97b/0x1690 net/netlink/af_netlink.c:2309 |
| In the Linux kernel, the following vulnerability has been resolved:
drm/scheduler: signal scheduled fence when kill job
When an entity from application B is killed, drm_sched_entity_kill()
removes all jobs belonging to that entity through
drm_sched_entity_kill_jobs_work(). If application A's job depends on a
scheduled fence from application B's job, and that fence is not properly
signaled during the killing process, application A's dependency cannot be
cleared.
This leads to application A hanging indefinitely while waiting for a
dependency that will never be resolved. Fix this issue by ensuring that
scheduled fences are properly signaled when an entity is killed, allowing
dependent applications to continue execution. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: Fix dangling pointer in krb_authenticate
krb_authenticate frees sess->user and does not set the pointer
to NULL. It calls ksmbd_krb5_authenticate to reinitialise
sess->user but that function may return without doing so. If
that happens then smb2_sess_setup, which calls krb_authenticate,
will be accessing free'd memory when it later uses sess->user. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: ctnetlink: remove refcounting in expectation dumpers
Same pattern as previous patch: do not keep the expectation object
alive via refcount, only store a cookie value and then use that
as the skip hint for dump resumption.
AFAICS this has the same issue as the one resolved in the conntrack
dumper, when we do
if (!refcount_inc_not_zero(&exp->use))
to increment the refcount, there is a chance that exp == last, which
causes a double-increment of the refcount and subsequent memory leak. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: Fix refcount leak for cifs_sb_tlink
Fix three refcount inconsistency issues related to `cifs_sb_tlink`.
Comments for `cifs_sb_tlink` state that `cifs_put_tlink()` needs to be
called after successful calls to `cifs_sb_tlink()`. Three calls fail to
update refcount accordingly, leading to possible resource leaks. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nft_ct: add seqadj extension for natted connections
Sequence adjustment may be required for FTP traffic with PASV/EPSV modes.
due to need to re-write packet payload (IP, port) on the ftp control
connection. This can require changes to the TCP length and expected
seq / ack_seq.
The easiest way to reproduce this issue is with PASV mode.
Example ruleset:
table inet ftp_nat {
ct helper ftp_helper {
type "ftp" protocol tcp
l3proto inet
}
chain prerouting {
type filter hook prerouting priority 0; policy accept;
tcp dport 21 ct state new ct helper set "ftp_helper"
}
}
table ip nat {
chain prerouting {
type nat hook prerouting priority -100; policy accept;
tcp dport 21 dnat ip prefix to ip daddr map {
192.168.100.1 : 192.168.13.2/32 }
}
chain postrouting {
type nat hook postrouting priority 100 ; policy accept;
tcp sport 21 snat ip prefix to ip saddr map {
192.168.13.2 : 192.168.100.1/32 }
}
}
Note that the ftp helper gets assigned *after* the dnat setup.
The inverse (nat after helper assign) is handled by an existing
check in nf_nat_setup_info() and will not show the problem.
Topoloy:
+-------------------+ +----------------------------------+
| FTP: 192.168.13.2 | <-> | NAT: 192.168.13.3, 192.168.100.1 |
+-------------------+ +----------------------------------+
|
+-----------------------+
| Client: 192.168.100.2 |
+-----------------------+
ftp nat changes do not work as expected in this case:
Connected to 192.168.100.1.
[..]
ftp> epsv
EPSV/EPRT on IPv4 off.
ftp> ls
227 Entering passive mode (192,168,100,1,209,129).
421 Service not available, remote server has closed connection.
Kernel logs:
Missing nfct_seqadj_ext_add() setup call
WARNING: CPU: 1 PID: 0 at net/netfilter/nf_conntrack_seqadj.c:41
[..]
__nf_nat_mangle_tcp_packet+0x100/0x160 [nf_nat]
nf_nat_ftp+0x142/0x280 [nf_nat_ftp]
help+0x4d1/0x880 [nf_conntrack_ftp]
nf_confirm+0x122/0x2e0 [nf_conntrack]
nf_hook_slow+0x3c/0xb0
..
Fix this by adding the required extension when a conntrack helper is assigned
to a connection that has a nat binding. |
