| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
i2c: imx: fix clock and pinctrl state inconsistency in runtime PM
In i2c_imx_runtime_suspend(), the clock is disabled before switching
the pinctrl state to sleep. If pinctrl_pm_select_sleep_state() fails,
the runtime suspend is aborted but the clock remains disabled, causing
a system crash when the hardware is subsequently accessed.
Fix this by switching the pinctrl state before disabling the clock so
that a pinctrl failure leaves the clock enabled and the hardware
accessible.
In i2c_imx_runtime_resume(), restore the pinctrl state back to sleep
if clk_enable() fails to keep the consistent. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: Don't WARN if memory is dirtied without a vCPU when the VM is dying
When marking a page dirty, complain about not having a running/loaded vCPU
if and only if the VM is still alive, i.e. its refcount is non-zero. This
will allow fixing a memory leak for x86 SEV-ES guests without hitting what
is effectively a false positive on the WARN.
For some SEV-ES VM-Exits, KVM keeps a writable mapping of a guest page
across an exit to userspace, and typically unmaps the page on the next
KVM_RUN. But if userspace never calls KVM_RUN after such an exit, then KVM
needs to unmap the page when the vCPU is destroyed, which in turn triggers
the WARN about not having a running vCPU.
Alternatively, SEV-ES could temporarily load the vCPU to suppress the WARN,
as is done in nested_vmx_free_vcpu() (but for completely unrelated reasons;
suppressing WARN from nested_put_vmcs12_pages() is pure happenstance). But
loading a vCPU during destruction is gross (ideally nVMX code would be
cleaned up), risks complicating the SEV-ES code (KVM would need to ensure
the temporarily load()+put() only runs when the vCPU isn't already loaded),
and is ultimately pointless.
The motivation for the WARN is to guard against KVM dirtying guest memory
without pushing the corresponding GFN to the active vCPU's dirty ring, e.g.
to ensure userspace doesn't miss a dirty page. But for the VM's refcount
to reach zero, there can't be _any_ userspace mappings to the dirty ring,
as mapping the dirty ring requires doing mmap() on the vCPU FD. I.e. if
userspace had a valid mapping for the dirty ring, then the vCPU file and
thus the owning VM would still be alive. And so since userspace can't
possibly reach the dirty ring, whether or not KVM technically "misses" a
push to the dirty ring is irrelevant. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_conntrack: destroy stale expectfn expectations on unregister
NAT helpers such as nf_nat_h323 store a raw pointer to module text in
exp->expectfn (e.g. ip_nat_q931_expect). nf_ct_helper_expectfn_unregister()
only unlinks the callback descriptor and never walks the expectation table,
so an expectation pending at module removal survives with a dangling
exp->expectfn into freed module text.
When the expected connection arrives, init_conntrack() invokes
exp->expectfn(), now a stale pointer into the unloaded module. Reproduced
on a KASAN build by loading the H.323 helpers, creating a Q.931
expectation, unloading nf_nat_h323, then connecting to the expected port:
Oops: int3: 0000 [#1] SMP KASAN NOPTI
RIP: 0010:0xffffffffa06102d1
init_conntrack.isra.0 (net/netfilter/nf_conntrack_core.c:1862)
nf_conntrack_in (net/netfilter/nf_conntrack_core.c:2049)
ipv4_conntrack_local (net/netfilter/nf_conntrack_proto.c:223)
nf_hook_slow (net/netfilter/core.c:619)
__ip_local_out (net/ipv4/ip_output.c:120)
__tcp_transmit_skb (net/ipv4/tcp_output.c:1715)
tcp_connect (net/ipv4/tcp_output.c:4374)
tcp_v4_connect (net/ipv4/tcp_ipv4.c:345)
__sys_connect (net/socket.c:2167)
Modules linked in: nf_conntrack_h323 [last unloaded: nf_nat_h323]
Reaching the dangling state requires CAP_SYS_MODULE in the initial user
namespace to remove a NAT helper that still has live expectations, so this
is a robustness fix; leaving an expectation pointing at freed text is wrong
regardless.
Add nf_ct_helper_expectfn_destroy(), which walks the expectation table and
drops every expectation whose ->expectfn matches the descriptor being torn
down. Call it from each NAT helper's exit path after the existing RCU grace
period, so no expectation outlives the code it points at and no extra
synchronize_rcu() is introduced. With the fix, the same reproducer runs to
completion without the Oops. |
| In the Linux kernel, the following vulnerability has been resolved:
hsr: Remove WARN_ONCE() in hsr_addr_is_self().
syzbot reported the warning [0] in hsr_addr_is_self(),
whose assumption is simply wrong.
hsr->self_node is cleared in hsr_del_self_node(), which
is called from hsr_dellink().
Since dev->rtnl_link_ops->dellink() is called before
unregister_netdevice_many(), there is a window when
user can find the device but without hsr->self_node.
Let's remove WARN_ONCE() in hsr_addr_is_self().
[0]:
HSR: No self node
WARNING: net/hsr/hsr_framereg.c:39 at hsr_addr_is_self+0x211/0x3f0 net/hsr/hsr_framereg.c:39, CPU#0: syz.4.16848/17220
Modules linked in:
CPU: 0 UID: 0 PID: 17220 Comm: syz.4.16848 Tainted: G L syzkaller #0 PREEMPT_{RT,(full)}
Tainted: [L]=SOFTLOCKUP
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/18/2026
RIP: 0010:hsr_addr_is_self+0x211/0x3f0 net/hsr/hsr_framereg.c:39
Code: 33 2f 41 0f b7 dd 89 ee 09 de 31 ff e8 c8 b4 c6 f6 09 dd 74 54 e8 0f b0 c6 f6 31 ed eb 53 e8 06 b0 c6 f6 48 8d 3d 2f 50 9c 04 <67> 48 0f b9 3a 31 ed eb 42 e8 c1 13 1f 00 89 c5 31 ff 89 c6 e8 96
RSP: 0018:ffffc900041c70e0 EFLAGS: 00010283
RAX: ffffffff8afdc6ca RBX: ffffffff8afdc4e6 RCX: 0000000000080000
RDX: ffffc90010493000 RSI: 0000000000000948 RDI: ffffffff8f9a1700
RBP: 0000000000000001 R08: 0000000000000000 R09: 0000000000000000
R10: ffffc900041c71e8 R11: fffff52000838e3f R12: dffffc0000000000
R13: ffff888041f9e3c0 R14: ffff888086ee3802 R15: 0000000000000000
FS: 00007f6fe985d6c0(0000) GS:ffff888126176000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f80bd437dac CR3: 0000000025096000 CR4: 00000000003526f0
DR0: ffffffffffffffff DR1: 00000000000001f8 DR2: 0000000000000002
DR3: ffffffffefffff15 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
check_local_dest net/hsr/hsr_forward.c:592 [inline]
fill_frame_info net/hsr/hsr_forward.c:728 [inline]
hsr_forward_skb+0xa11/0x2a80 net/hsr/hsr_forward.c:739
hsr_dev_xmit+0x253/0x370 net/hsr/hsr_device.c:236
__netdev_start_xmit include/linux/netdevice.h:5368 [inline]
netdev_start_xmit include/linux/netdevice.h:5377 [inline]
xmit_one net/core/dev.c:3888 [inline]
dev_hard_start_xmit+0x2df/0x860 net/core/dev.c:3904
__dev_queue_xmit+0x1428/0x3900 net/core/dev.c:4870
neigh_output include/net/neighbour.h:556 [inline]
ip_finish_output2+0xcec/0x10b0 net/ipv4/ip_output.c:237
ip_send_skb net/ipv4/ip_output.c:1510 [inline]
ip_push_pending_frames+0x8b/0x110 net/ipv4/ip_output.c:1530
raw_sendmsg+0x1547/0x1a50 net/ipv4/raw.c:659
sock_sendmsg_nosec net/socket.c:787 [inline]
__sock_sendmsg net/socket.c:802 [inline]
____sys_sendmsg+0x7da/0x9c0 net/socket.c:2698
___sys_sendmsg+0x2a5/0x360 net/socket.c:2752
__sys_sendmsg net/socket.c:2784 [inline]
__do_sys_sendmsg net/socket.c:2789 [inline]
__se_sys_sendmsg net/socket.c:2787 [inline]
__x64_sys_sendmsg+0x1c3/0x2a0 net/socket.c:2787
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0x15f/0xf80 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7f6feb62ce59
Code: ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 e8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f6fe985d028 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007f6feb8a6090 RCX: 00007f6feb62ce59
RDX: 0000000000000000 RSI: 0000200000000000 RDI: 0000000000000004
RBP: 00007f6feb6c2d6f R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 00007f6feb8a6128 R14: 00007f6feb8a6090 R15: 00007ffcf01cc488
</TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Fix out-of-bounds read in dp_get_eq_aux_rd_interval()
[Why & How]
The aux_rd_interval array in struct dc_lttpr_caps is declared with
MAX_REPEATER_CNT - 1 (7) elements, indexed 0..6. However, the offset
parameter passed to dp_get_eq_aux_rd_interval() can be as large as
MAX_REPEATER_CNT (8) when a sink reports 8 LTTPR repeaters via DPCD.
This leads to an out-of-bounds read of aux_rd_interval[7] when offset
is 8.
Fix this by growing aux_rd_interval to MAX_REPEATER_CNT elements to
accommodate the full range of valid repeater counts defined by the DP
spec.
(cherry picked from commit a55a458a8df37a65ffda5cf721d554a8f74f6b04) |
| In the Linux kernel, the following vulnerability has been resolved:
net: bonding: fix NULL pointer dereference in bond_do_ioctl()
In bond_do_ioctl(), slave_dev is obtained via __dev_get_by_name() which
can return NULL if the requested interface name does not exist. However,
the subsequent slave_dbg() call is placed before the NULL check:
slave_dev = __dev_get_by_name(net, ifr->ifr_slave);
slave_dbg(bond_dev, slave_dev, "slave_dev=%p:\n", slave_dev); //here
if (!slave_dev)
return -ENODEV;
The slave_dbg() macro expands to netdev_dbg(bond_dev, "(slave %s): " fmt,
(slave_dev)->name, ...) which unconditionally dereferences slave_dev->name
before the NULL check is performed. This results in a NULL pointer
dereference kernel oops when a user calls bonding ioctl (e.g.
SIOCBONDENSLAVE, SIOCBONDRELEASE, etc.) with a non-existent slave
interface name.
This is reachable from userspace via the bonding ioctl interface with
CAP_NET_ADMIN capability, making it a potential local denial-of-service
vector.
Fix by moving the slave_dbg() call after the NULL check. |
| In the Linux kernel, the following vulnerability has been resolved:
i2c: qcom-cci: Fix NULL pointer dereference in cci_remove()
On all modern platforms Qualcomm CCI controller provides two I2C masters,
and on particular boards only one I2C master may be initialized, and in
such cases the device unbinding or driver removal causes a NULL pointer
dereference, because cci_halt() is called for all two I2C masters, but
a completion is initialized only for the single enabled master:
% rmmod i2c-qcom-cci
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
<snip>
Call trace:
__wait_for_common+0x194/0x1a8 (P)
wait_for_completion_timeout+0x20/0x2c
cci_remove+0xc4/0x138 [i2c_qcom_cci]
platform_remove+0x20/0x30
device_remove+0x4c/0x80
device_release_driver_internal+0x1c8/0x224
driver_detach+0x50/0x98
bus_remove_driver+0x6c/0xbc
driver_unregister+0x30/0x60
platform_driver_unregister+0x14/0x20
qcom_cci_driver_exit+0x18/0x1008 [i2c_qcom_cci]
.... |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: SDCA: fix NULL pointer dereference in sdca_dev_unregister_functions
sdca_dev_unregister_functions() iterates over all SDCA function
descriptors and calls sdca_dev_unregister() on each func_dev without
checking for NULL. When a function registration has failed partway
through, or the device cleanup races with probe deferral, func_dev
entries may be NULL, leading to a kernel oops:
BUG: kernel NULL pointer dereference, address: 0000000000000040
RIP: 0010:device_del+0x1e/0x3e0
Call Trace:
sdca_dev_unregister_functions+0x37/0x60 [snd_soc_sdca]
release_nodes+0x35/0xb0
devres_release_all+0x90/0x100
device_unbind_cleanup+0xe/0x80
device_release_driver_internal+0x1c1/0x200
bus_remove_device+0xc6/0x130
device_del+0x161/0x3e0
device_unregister+0x17/0x60
sdw_delete_slave+0xb6/0xd0 [soundwire_bus]
sdw_bus_master_delete+0x1e/0x50 [soundwire_bus]
...
sof_probe_work+0x19/0x30 [snd_sof]
This was observed on a Lenovo ThinkPad X1 Carbon G14 (Panther Lake)
with the SOF audio driver probe failing due to missing Panther Lake
firmware, causing the subsequent cleanup of SoundWire devices to
trigger the crash.
Fix this with three changes:
1) Add a NULL guard in sdca_dev_unregister() so that callers do not
need to pre-validate the pointer (defense in depth).
2) In sdca_dev_unregister_functions(), skip NULL func_dev entries
and clear func_dev to NULL after unregistration, making the
function idempotent and safe against double-invocation.
3) In sdca_dev_register_functions(), roll back all previously
registered functions when a later one fails, so the function
array is never left in a partially-populated state. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: wm_adsp: Fix NULL dereference when removing firmware controls
In wm_adsp_control_remove() check that the priv pointer is not NULL
before attempting to cleanup what it points to.
When cs_dsp creates a control it calls wm_adsp_control_add_cb() so that
wm_adsp can create its own private control data. There are two cases
where private data is not created:
1. The control is a SYSTEM control, so an ALSA control is not created.
2. The codec driver has registered a control_add() callback that
hides the control, so wm_adsp_control_add() is not called.
When cs_dsp_remove destroys its control list it calls
wm_adsp_control_remove() for each control. But wm_adsp_control_remove()
was attempting to cleanup the private data pointed to by cs_ctl->priv
without checking the pointer for NULL. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/damon/reclaim: handle ctx allocation failure
Patch series "mm/damon/{reclaim,lru_sort}: handle ctx allocation failures".
DAMON_RECLAIM and DAMON_LRU_SORT could dereference NULL pointers if their
damon_ctx object allocations fail. The bugs are expected to happen
infrequently because the allocations are arguably too small to fail on
common setups. But theoretically they are possible and the consequences
are bad. Fix those.
The issues were discovered [1] by Sashiko.
This patch (of 2):
DAMON_RECLAIM allocates the damon_ctx object for its kdamond in its init
function. damon_reclaim_enabled_store() wrongly assumes the allocation
will always succeed once tried. If the damon_ctx allocation was failed,
therefore, code execution reaches to damon_commit_ctx() while 'ctx' is
NULL. As a result, it dereferences the NULL 'ctx' pointer. Avoid the
NULL dereference by returning -ENOMEM if 'ctx' is NULL. |
| In the Linux kernel, the following vulnerability has been resolved:
pinctrl: mcp23s08: Initialize mcp->dev and mcp->addr before regmap init
Regmap initialization triggers regcache_maple_populate() which attempts
SPI read to populate cache. SPI read requires mcp->dev and mcp->addr to
be set, without them, NULL pointer dereference occurs during probe.
Move initialization before mcp23s08_spi_regmap_init() call. |
| In the Linux kernel, the following vulnerability has been resolved:
net: airoha: Add NULL check for of_reserved_mem_lookup() in airoha_qdma_init_hfwd_queues()
of_reserved_mem_lookup() may return NULL if the reserved memory region
referenced by the "memory-region" phandle is not found in the reserved
memory table (e.g. due to a misconfigured DTS or a removed
memory-region node). The current code dereferences the returned
pointer without checking for NULL, leading to a kernel NULL pointer
dereference at the following lines:
dma_addr = rmem->base; // line 1156
num_desc = div_u64(rmem->size, buf_size); // line 1160
Add a NULL check after of_reserved_mem_lookup() and return -ENODEV if
the lookup fails, which is consistent with the existing error handling
for of_parse_phandle() failure in the same code block. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/damon/lru_sort: handle ctx allocation failure
DAMON_LRU_SORT allocates the damon_ctx object for its kdamond in its init
function. damon_lru_sort_enabled_store() wrongly assumes the allocation
will always succeed once tried. If the damon_ctx allocation was failed,
therefore, code execution reaches to damon_commit_ctx() while 'ctx' is
NULL. As a result, it dereferences the NULL 'ctx' pointer. Avoid the
NULL dereference by returning -ENOMEM if 'ctx' is NULL. |
| In the Linux kernel, the following vulnerability has been resolved:
Revert "wireguard: device: enable threaded NAPI"
This reverts commit 933466fc50a8e4eb167acbd0d8ec96a078462e9c which is
commit db9ae3b6b43c79b1ba87eea849fd65efa05b4b2e upstream.
We have had three independent production user reports in combination
with Cilium utilizing WireGuard as encryption underneath that k8s Pod
E/W traffic to certain peer nodes fully stalled. The situation appears
as follows:
- Occurs very rarely but at random times under heavy networking load.
- Once the issue triggers the decryption side stops working completely
for that WireGuard peer, other peers keep working fine. The stall
happens also for newly initiated connections towards that particular
WireGuard peer.
- Only the decryption side is affected, never the encryption side.
- Once it triggers, it never recovers and remains in this state,
the CPU/mem on that node looks normal, no leak, busy loop or crash.
- bpftrace on the affected system shows that wg_prev_queue_enqueue
fails, thus the MAX_QUEUED_PACKETS (1024 skbs!) for the peer's
rx_queue is reached.
- Also, bpftrace shows that wg_packet_rx_poll for that peer is never
called again after reaching this state for that peer. For other
peers wg_packet_rx_poll does get called normally.
- Commit db9ae3b ("wireguard: device: enable threaded NAPI")
switched WireGuard to threaded NAPI by default. The default has
not been changed for triggering the issue, neither did CPU
hotplugging occur (i.e. 5bd8de2 ("wireguard: queueing: always
return valid online CPU in wg_cpumask_choose_online()")).
- The issue has been observed with stable kernels of v5.15 as well as
v6.1. It was reported to us that v5.10 stable is working fine, and
no report on v6.6 stable either (somewhat related discussion in [0]
though).
- In the WireGuard driver the only material difference between v5.10
stable and v5.15 stable is the switch to threaded NAPI by default.
[0] https://lore.kernel.org/netdev/CA+wXwBTT74RErDGAnj98PqS=wvdh8eM1pi4q6tTdExtjnokKqA@mail.gmail.com/
Breakdown of the problem:
1) skbs arriving for decryption are enqueued to the peer->rx_queue in
wg_packet_consume_data via wg_queue_enqueue_per_device_and_peer.
2) The latter only moves the skb into the MPSC peer queue if it does
not surpass MAX_QUEUED_PACKETS (1024) which is kept track in an
atomic counter via wg_prev_queue_enqueue.
3) In case enqueueing was successful, the skb is also queued up
in the device queue, round-robin picks a next online CPU, and
schedules the decryption worker.
4) The wg_packet_decrypt_worker, once scheduled, picks these up
from the queue, decrypts the packets and once done calls into
wg_queue_enqueue_per_peer_rx.
5) The latter updates the state to PACKET_STATE_CRYPTED on success
and calls napi_schedule on the per peer->napi instance.
6) NAPI then polls via wg_packet_rx_poll. wg_prev_queue_peek checks
on the peer->rx_queue. It will wg_prev_queue_dequeue if the
queue->peeked skb was not cached yet, or just return the latter
otherwise. (wg_prev_queue_drop_peeked later clears the cache.)
7) From an ordering perspective, the peer->rx_queue has skbs in order
while the device queue with the per-CPU worker threads from a
global ordering PoV can finish the decryption and signal the skb
PACKET_STATE_CRYPTED out of order.
8) A situation can be observed that the first packet coming in will
be stuck waiting for the decryption worker to be scheduled for
a longer time when the system is under pressure.
9) While this is the case, the other CPUs in the meantime finish
decryption and call into napi_schedule.
10) Now in wg_packet_rx_poll it picks up the first in-order skb
from the peer->rx_queue and sees that its state is still
PACKET_STATE_UNCRYPTED. The NAPI poll routine then exits e
---truncated--- |
| A vulnerability was found in systemd-coredump. This flaw allows an attacker to force a SUID process to crash and replace it with a non-SUID binary to access the original's privileged process coredump, allowing the attacker to read sensitive data, such as /etc/shadow content, loaded by the original process.
A SUID binary or process has a special type of permission, which allows the process to run with the file owner's permissions, regardless of the user executing the binary. This allows the process to access more restricted data than unprivileged users or processes would be able to. An attacker can leverage this flaw by forcing a SUID process to crash and force the Linux kernel to recycle the process PID before systemd-coredump can analyze the /proc/pid/auxv file. If the attacker wins the race condition, they gain access to the original's SUID process coredump file. They can read sensitive content loaded into memory by the original binary, affecting data confidentiality. |
| In the Linux kernel, the following vulnerability has been resolved:
platform/x86: dell-wmi-sysman: bound enumeration string aggregation
populate_enum_data() aggregates firmware-provided value-modifier
and possible-value strings into fixed 512-byte struct members.
The current code bounds each individual source string but then
appends every string and separator with raw strcat() and no
remaining-space check.
Switch the aggregation loops to a bounded append helper and
reject enumeration packages whose combined strings do not fit
in the destination buffers.
[ij: add include] |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: fix leak if split 6 GHz scanning fails
rdev->int_scan_req is leaked if cfg80211_scan() fails. Note that it's
supposed to be released at ___cfg80211_scan_done() but this doesn't happen
as rdev->scan_req is NULL at that point, too, leading to the early return
from the freeing function.
unreferenced object 0xffff8881161d0800 (size 512):
comm "wpa_supplicant", pid 379, jiffies 4294749765
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 f0 81 13 16 81 88 ff ff ................
backtrace (crc c867fdb6):
kmemleak_alloc+0x89/0x90
__kmalloc_noprof+0x2fd/0x410
cfg80211_scan+0x133/0x730
nl80211_trigger_scan+0xc69/0x1cc0
genl_family_rcv_msg_doit+0x204/0x2f0
genl_rcv_msg+0x431/0x6b0
netlink_rcv_skb+0x143/0x3f0
genl_rcv+0x27/0x40
netlink_unicast+0x4f6/0x820
netlink_sendmsg+0x797/0xce0
__sock_sendmsg+0xc4/0x160
____sys_sendmsg+0x5e4/0x890
___sys_sendmsg+0xf8/0x180
__sys_sendmsg+0x136/0x1e0
__x64_sys_sendmsg+0x76/0xc0
x64_sys_call+0x13f0/0x17d0
Found by Linux Verification Center (linuxtesting.org). |
| In the Linux kernel, the following vulnerability has been resolved:
padata: Put CPU offline callback in ONLINE section to allow failure
syzbot reported the following warning:
DEAD callback error for CPU1
WARNING: kernel/cpu.c:1463 at _cpu_down+0x759/0x1020 kernel/cpu.c:1463, CPU#0: syz.0.1960/14614
at commit 4ae12d8bd9a8 ("Merge tag 'kbuild-fixes-7.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kbuild/linux")
which tglx traced to padata_cpu_dead() given it's the only
sub-CPUHP_TEARDOWN_CPU callback that returns an error.
Failure isn't allowed in hotplug states before CPUHP_TEARDOWN_CPU
so move the CPU offline callback to the ONLINE section where failure is
possible. |
| In the Linux kernel, the following vulnerability has been resolved:
vsock/vmci: fix sk_ack_backlog leak on failed handshake
When vmci_transport_recv_connecting_server() returns an error,
vmci_transport_recv_listen() calls vsock_remove_pending() but never
calls sk_acceptq_removed(). This leaves sk_ack_backlog incremented
permanently.
Repeated handshake failures (malformed packets, queue pair alloc
failure, event subscribe failure) cause sk_ack_backlog to climb
toward sk_max_ack_backlog. Once it reaches the limit the listener
permanently refuses all new connections with -ECONNREFUSED, a
silent denial of service requiring a process restart to recover.
The two existing sk_acceptq_removed() calls in af_vsock.c do not
cover this path: line 764 checks vsock_is_pending() which returns
false after vsock_remove_pending(), and line 1889 is only reached
on successful accept().
Fix by balancing sk_acceptq_added() with sk_acceptq_removed() on
the error path. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/virtio: fix dma_fence refcount leak on error in virtio_gpu_dma_fence_wait()
dma_fence_unwrap_for_each() internally calls dma_fence_unwrap_first()
which does cursor->chain = dma_fence_get(head), taking an extra
reference. On normal loop completion, dma_fence_unwrap_next()
releases this via dma_fence_chain_walk() -> dma_fence_put().
When virtio_gpu_do_fence_wait() fails and the function returns early
from inside the loop, the cursor->chain reference is never released.
This is the only caller in the entire kernel that does an early return
inside dma_fence_unwrap_for_each.
Add dma_fence_put(itr.chain) before the early return. |
