| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
iio: pressure: mpl115: fix runtime PM leak on read error
mpl115_read_raw() takes a runtime PM reference with pm_runtime_get_sync()
before reading the processed pressure or raw temperature, but on the read
error path it returns without calling pm_runtime_put_autosuspend(). Each
failed read therefore leaks a runtime PM reference and prevents the device
from autosuspending.
Drop the reference before checking the return value so both the success
and error paths are balanced. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: gyro: bmg160: bail out when bandwidth/filter is not in table
bmg160_get_filter() walks bmg160_samp_freq_table[] looking for the entry
matching the bw_bits value read from the chip:
for (i = 0; i < ARRAY_SIZE(bmg160_samp_freq_table); ++i) {
if (bmg160_samp_freq_table[i].bw_bits == bw_bits)
break;
}
*val = bmg160_samp_freq_table[i].filter;
If no entry matches, i ends up equal to the array size and the next line
reads one slot past the end. bmg160_set_filter() has the same shape, driven
by 'val' instead of bw_bits.
smatch flags both:
drivers/iio/gyro/bmg160_core.c:204 bmg160_get_filter() error:
buffer overflow 'bmg160_samp_freq_table' 7 <= 7
drivers/iio/gyro/bmg160_core.c:222 bmg160_set_filter() error:
buffer overflow 'bmg160_samp_freq_table' 7 <= 7
Return -EINVAL when no entry matches.
The set_filter() path is reachable from userspace via the sysfs
in_anglvel_filter_low_pass_3db_frequency interface, so userspace can
trivially trigger the out-of-bounds read with a value that is not in
bmg160_samp_freq_table[].filter. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: chemical: scd30: Cleanup initializations and fix sign-extension bug
Include linux/bitfield.h for FIELD_GET().
Create new macros for bit manipulation in combination with manual bit
manipulation being replaced with FIELD_GET().
The current variable declaration and initializations are barely readable
and use comma separations across multiple lines. Refactor the
initializations so that mantissa and exp have separate declarations and
sign gets initialized later.
In addition (and due to the nature of the cleanup), fix a sign-extension
bug where, float32 would get bitwise anded with ~BIT(31)
(which is 0xFFFFFFFF7FFFFFFF) which corrupted the exponent. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: adc: ad_sigma_delta: fix CS held asserted and state leaks
In ad_sigma_delta_single_conversion(), set_mode(AD_SD_MODE_IDLE) and
disable_one() were called from the out: block while keep_cs_asserted
was still true. This caused any SPI transfer issued by those callbacks
to carry cs_change=1, leaving CS permanently asserted after the
conversion. Fix by moving both calls into the out_unlock: block, after
keep_cs_asserted is cleared, matching the pattern already used in
ad_sd_calibrate().
In the error path of ad_sd_buffer_postenable(), if an operation fails
after set_mode(AD_SD_MODE_CONTINUOUS) has already succeeded (e.g.
spi_offload_trigger_enable()), the device is left in continuous
conversion mode with CS physically asserted. Additionally,
bus_locked remaining true after spi_bus_unlock() causes subsequent
SPI operations to call spi_sync_locked() without the bus lock actually
held, allowing concurrent SPI access.
Fix the error path by clearing keep_cs_asserted first, then calling
set_mode(AD_SD_MODE_IDLE) to revert the device mode and deassert CS,
then clearing bus_locked before releasing the bus.
For devices that implement neither set_mode nor disable_one (such as
MAX11205, which has no physical CS pin), no SPI transfer is issued
during cleanup and the cs_change flag has no effect on any physical
line. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: adc: ad_sigma_delta: fix clear_pending_event for registerless devices
ad_sigma_delta_clear_pending_event() falls through to the status register
read path for devices with has_registers = false and no rdy_gpiod. For
such devices, ad_sd_read_reg() skips the address byte entirely and clocks
raw MISO bytes with no address phase — making it byte-for-byte identical
to reading conversion data. If a pending conversion result is present,
this partially consumes it and corrupts the data stream for the subsequent
ad_sd_read_reg() call in ad_sigma_delta_single_conversion().
Furthermore, with num_resetclks = 0 on these devices, data_read_len
evaluates to 0. If the clocked byte has bit 7 clear, pending_event is set
and the code attempts memset(data + 2, 0xff, 0 - 1), overflowing to
SIZE_MAX and corrupting the heap.
Fix by returning 0 immediately when neither rdy_gpiod nor has_registers
is set. This is safe for all current registerless devices: ad7191 and
ad7780 (with powerdown GPIO) are reset between conversions by CS
deassertion, so there is no stale result to drain; ad7780 (without
powerdown GPIO) and max11205 are continuously-converting and cycle ~DRDY
at the output data rate regardless of whether the previous result was
read, so the next falling edge fires naturally.
A future registerless device that holds ~DRDY asserted until data is read
would be broken by this early return and would require either
num_resetclks set or a rdy-gpio.
The same heap corruption is reachable on any device with rdy_gpiod set
but num_resetclks = 0: if the GPIO indicates a pending event, the drain
path executes memset(data + 2, 0xff, 0 - 1) regardless of has_registers.
Add an explicit data_read_len == 0 guard after the pending event check;
the stale result is then consumed by the first ad_sd_read_reg() call in
ad_sigma_delta_single_conversion(). |
| In the Linux kernel, the following vulnerability has been resolved:
ACPI: NFIT: core: Fix acpi_nfit_init() error cleanup
If acpi_nfit_init() fails after adding the acpi_desc object to the
acpi_descs list, that object is never removed from that list because
the acpi_nfit_shutdown() devm action is not added for the NFIT device
in that case. Next, the acpi_nfit_init() failure causes
acpi_nfit_probe() to fail, the acpi_desc object is freed, and a
dangling pointer is left behind in the acpi_descs. Any subsequent
ACPI Machine Check Exception will trigger nfit_handle_mce() which
iterates over acpi_descs and so a use-after-free will occur.
Moreover, if acpi_nfit_probe() returns 0 after installing a notify
handler for the NFIT device and without allocating the acpi_desc
object and setting the NFIT device's driver data pointer, the
acpi_desc object will be allocated by acpi_nfit_update_notify()
and acpi_nfit_init() will be called to initialize it. Regardless
of whether or not acpi_nfit_init() fails in that case, the
acpi_nfit_shutdown() devm action is not added for the NFIT device
and acpi_desc is never removed from the acpi_descs list. If the
acpi_desc object is freed subsequently on driver removal, any
subsequent ACPI MCE will lead to a use-after-free like in the
previous case.
To address the first issue mentioned above, make acpi_nfit_probe()
call acpi_nfit_shutdown() directly on acpi_nfit_init() failures and
to address the other one, add a remove callback to the driver and
make it call acpi_nfit_shutdown(). Also, since it is now possible to
pass NULL to acpi_nfit_shutdown() or the acpi_desc object passed to it
may not have been initialized, add checks against NULL for acpi_desc and
its nvdimm_bus field to that function and make acpi_nfit_unregister()
clear the latter after unregistering the NVDIMM bus. |
| In the Linux kernel, the following vulnerability has been resolved:
ACPI: CPPC: Suppress UBSAN warning caused by field misuse
The definition of reg->access_width changes depending on the
reg->space_id type. Type ACPI_ADR_SPACE_PLATFORM_COMM uses
access_width to indicate the PCC region, which can result in a UBSAN
if the value is greater than 4.
For example:
UBSAN: shift-out-of-bounds in drivers/acpi/cppc_acpi.c:1090:9
shift exponent 32 is too large for 32-bit type 'int'
CPU: 61 UID: 0 PID: 1220 Comm: (udev-worker) Not tainted 7.0.10-201.fc44.aarch64 #1 PREEMPT(lazy)
Hardware name: To be filled by O.E.M.
Call trace:
...(trimming)
ubsan_epilogue+0x10/0x48
__ubsan_handle_shift_out_of_bounds+0xdc/0x1e0
cpc_write+0x4d0/0x670
cppc_set_perf+0x18c/0x490
cppc_cpufreq_cpu_init+0x1c8/0x380 [cppc_cpufreq]
... (trimming)
Lets fix this by validating the region type, as well as whether
access_width has a value. Then since we are returning bit_width
directly for ACPI_ADR_SPACE_PLATFORM_COMM, drop the code correcting
the size. |
| In the Linux kernel, the following vulnerability has been resolved:
firmware: arm_ffa: Bound PARTITION_INFO_GET_REGS copies
The register-based PARTITION_INFO_GET path trusted the firmware-provided
indices when copying partition descriptors into the caller buffer.
Reject inconsistent counts or index progressions so the copy loop cannot
write past the allocated array.
(fixed cur_idx when exactly one descriptor in the first fragment) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/hyperv: validate resolution_count and fix WIN8 fallback
A SYNTHVID_RESOLUTION_RESPONSE with resolution_count > 64 walks past
the supported_resolution[SYNTHVID_MAX_RESOLUTION_COUNT] array in the
parse loop. Bound resolution_count against the array size, folded
into the existing zero-check.
When the WIN10 resolution probe fails, the caller in
hyperv_connect_vsp() left hv->screen_*_max / preferred_* unpopulated,
which sets mode_config.max_width / max_height to 0 and makes
drm_internal_framebuffer_create() reject every userspace framebuffer
with -EINVAL. The pre-WIN10 branch had the same gap for
preferred_width / preferred_height. Use a single post-probe fallback
guarded by screen_width_max == 0 so both paths converge on the WIN8
defaults. |
| In the Linux kernel, the following vulnerability has been resolved:
ethtool: tsconfig: fix missing ethnl_ops_complete()
tsconfig_prepare_data() calls ethnl_ops_begin(), we need to call
ethnl_ops_complete() before returning the error. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/ntfs3: bound NTFS_DE view.data_off in UpdateRecordData{Root,Allocation}
In do_action()'s UpdateRecordDataRoot (fslog.c:3489) and
UpdateRecordDataAllocation (fslog.c:3697) cases, the memmove
destination is `Add2Ptr(e, le16_to_cpu(e->view.data_off))`,
where e->view.data_off comes from an on-disk NTFS_DE inside
an INDEX_ROOT or INDEX_BUFFER. Neither case validates
view.data_off + dlen against e->size; the existing
check_if_index_root / check_if_alloc_index helpers walk the
entry chain and validate the entry's offset, but not its
internal view fields.
The neighbouring read sites (e.g., fs/ntfs3/index.c when
iterating view entries) check view.data_off + view.data_size
<= e->size. Apply the same bound at the two memmove sites.
Reproduced under UML+KASAN on mainline 8d90b09e6741 via
pr_warn-only probe instrumentation: with view.data_off forced
to 0xFFFC, the memmove writes 32 bytes past the end of the
NTFS_DE.
This is similar in shape to Pavitra Jha's 2026-05-02 patch
"fs/ntfs3: prevent oob in case UpdateRecordDataRoot"
(<20260502105008.21827-1-jhapavitra98@gmail.com>) which
proposes calling ntfs3_bad_de_range(); that helper does not
exist in mainline. This patch uses inline checks. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: bridge: fix stale prevhdr pointer in br_ip6_fragment()
br_ip6_fragment() gets prevhdr, a pointer into the skb head, from
ip6_find_1stfragopt(), then calls skb_checksum_help(). For a cloned skb
skb_checksum_help() reallocates the head via pskb_expand_head(), leaving
prevhdr dangling. It is later dereferenced in ip6_frag_next(), causing a
use-after-free write.
Save prevhdr's offset before skb_checksum_help() and recompute it after,
like commit ef0efcd3bd3f ("ipv6: Fix dangling pointer when ipv6
fragment").
BUG: KASAN: slab-use-after-free in ip6_frag_next (net/ipv6/ip6_output.c:857)
Write of size 1 at addr ffff888013ff5016 by task exploit/141
Call Trace:
...
kasan_report (mm/kasan/report.c:595)
ip6_frag_next (net/ipv6/ip6_output.c:857)
br_ip6_fragment (net/ipv6/netfilter.c:212)
nf_ct_bridge_post (net/bridge/netfilter/nf_conntrack_bridge.c:407)
nf_hook_slow (net/netfilter/core.c:619)
br_forward_finish (net/bridge/br_forward.c:66)
__br_forward (net/bridge/br_forward.c:115)
maybe_deliver (net/bridge/br_forward.c:191)
br_flood (net/bridge/br_forward.c:245)
br_handle_frame_finish (net/bridge/br_input.c:229)
br_handle_frame (net/bridge/br_input.c:442)
...
packet_sendmsg (net/packet/af_packet.c:3114)
...
do_syscall_64 (arch/x86/entry/syscall_64.c:94)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:121)
Kernel panic - not syncing: Fatal exception in interrupt |
| In the Linux kernel, the following vulnerability has been resolved:
ethtool: rss: fix indir_table and hkey leak on get_rxfh failure
rss_prepare_get() allocates the indirection table and hash key buffer
via rss_get_data_alloc(), then calls ops->get_rxfh() to populate them.
If get_rxfh() fails, the function returns an error without freeing
the allocation. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe/oa: Fix exec_queue leak on width check in stream open
In xe_oa_stream_open_ioctl(), when param.exec_q->width > 1 the
function returns -EOPNOTSUPP directly, skipping the existing
err_exec_q cleanup path. The exec_queue reference obtained by
xe_exec_queue_lookup() is leaked.
The exec queue holds a reference on the xe_file, which is only
dropped during queue teardown. The leaked lookup ref is not on
the file's exec_queue xarray, so file close cannot release it.
This keeps both the exec queue and the file private state pinned
indefinitely.
Jump to err_exec_q instead of returning directly so the reference
is released.
(cherry picked from commit 339fa0be9e4a5d69fa47e91f4a36574224fb478f) |
| In the Linux kernel, the following vulnerability has been resolved:
bpf, skmsg: fix verdict sk_data_ready racing with ktls rx
sk_psock_strp_data_ready() already checks tls_sw_has_ctx_rx() and
defers to psock->saved_data_ready when a TLS RX context is present,
avoiding a conflict with the TLS strparser's ownership of the receive
queue (commit e91de6afa81c, "bpf: Fix running sk_skb program types
with ktls").
sk_psock_verdict_data_ready() has no equivalent guard. When a socket
is inserted into a sockmap (BPF_SK_SKB_VERDICT) before TLS RX is
configured, tls_sw_strparser_arm() saves sk_psock_verdict_data_ready
as rx_ctx->saved_data_ready. On data arrival:
tls_data_ready -> tls_strp_data_ready -> tls_rx_msg_ready
-> saved_data_ready() = sk_psock_verdict_data_ready()
-> tcp_read_skb() drains sk_receive_queue via __skb_unlink()
without calling tcp_eat_skb(), so copied_seq is not advanced.
tls_strp_msg_load() then finds tcp_inq() >= full_len (stale), calls
tcp_recv_skb() on the now-empty queue, hits WARN_ON_ONCE(!first), and
returns with rx_ctx->strp.anchor.frag_list pointing at a psock-owned
(potentially freed) skb. tls_decrypt_sg() subsequently walks that
frag_list: use-after-free.
Apply the same fix as sk_psock_strp_data_ready(): if a TLS RX context
is present, call psock->saved_data_ready (sock_def_readable) to wake
recv() waiters and return immediately, leaving the receive queue
untouched. TLS retains sole ownership of the queue and decrypts the
record normally through tls_sw_recvmsg(). |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: bounds-check link_id in ieee80211_ml_epcs
IEEE80211_MLE_STA_EPCS_CONTROL_LINK_ID is 0x000f, so link_id extracted
from a PRIO_ACCESS ML element PER_STA_PROFILE subelement can be 0..15.
sdata->link[] has IEEE80211_MLD_MAX_NUM_LINKS (15) entries (indices 0..14),
making index 15 out-of-bounds.
A connected WiFi 7 AP can trigger this by sending an EPCS Enable Response
action frame with a PER_STA_PROFILE subelement where link_id = 15. The
unsolicited-notification path (dialog_token = 0) is reachable any time
EPCS is already enabled, without any prior client request.
sdata->link[15] reads into the first word of sdata->activate_links_work
(a wiphy_work whose embedded list_head is non-NULL after INIT_LIST_HEAD),
so the NULL check on the result does not catch the invalid access. The
garbage pointer is then passed to ieee80211_sta_wmm_params(), which
dereferences link->sdata and crashes the kernel.
The same class of bug was fixed for ieee80211_ml_reconfiguration() by
commit 162d331d833d ("wifi: mac80211: bounds-check link_id in
ieee80211_ml_reconfiguration"). |
| In the Linux kernel, the following vulnerability has been resolved:
erofs: fix managed cache race for unaligned extents
After unaligned compressed extents were introduced, the following race
could occur:
[Thread 1] [Thread 2]
(z_erofs_fill_bio_vec)
<handle a Z_EROFS_PREALLOCATED_FOLIO folio>
...
filemap_add_folio (1)
(z_erofs_bind_cache)
<the same folio is found..>
..
..
folio_attach_private (2)
filemap_add_folio (3) again
Since (1) is executed but (2) hasn't been executed yet, it's possible
that another thread finds the same managed folio in z_erofs_bind_cache()
for a different pcluster and calls filemap_add_folio() again since
folio->private is still Z_EROFS_PREALLOCATED_FOLIO.
Fix this by explicitly clearing folio->private before making the folio
visible in the managed cache so that another pcluster can simply wait
on the locked managed folio as what we did for other shared cases [1].
This only impacts unaligned data compression (`-E48bit` with zstd,
for example).
[1] Commit 9e2f9d34dd12 ("erofs: handle overlapped pclusters out of
crafted images properly") was originally introduced to handle crafted
overlapped extents, but it addresses unaligned extents as well. |
| In the Linux kernel, the following vulnerability has been resolved:
dma-mapping: move dma_map_resource() sanity check into debug code
dma_map_resource() uses pfn_valid() to ensure the range is not RAM.
However, pfn_valid() only checks for availability of the memory map for
a PFN but it does not ensure that the PFN is actually backed by RAM. On
ARM64 with SPARSEMEM (128MB section granularity), MMIO addresses that
share a section with RAM will falsely trigger the WARN_ON_ONCE and cause
dma_map_resource() to return DMA_MAPPING_ERROR.
This causes a WARNING on Raspberry Pi 4 during spi_bcm2835 probe because
the SPI FIFO register (0xfe204004) falls in the same sparsemem section
as the end of RAM (0xf8000000-0xfbffffff), both in section 31
(0xf8000000-0xffffffff).
Move the sanity check from dma_map_resource() into debug_dma_map_phys()
and replace the unreliable pfn_valid() with pfn_valid() &&
!PageReserved(), which correctly identifies actual usable RAM without
false positives for MMIO regions that happen to have struct pages.
Since dma_map_resource() is dma_map_phys(DMA_ATTR_MMIO), the check
applies equally to both APIs. Any non-reserved page represents kernel
memory to a sufficient degree that using DMA_ATTR_MMIO on it is almost
certainly wrong and risks breaking coherency on non-coherent platforms.
ZONE_DEVICE pages used for PCI P2P DMA (MEMORY_DEVICE_PCI_P2PDMA) have
PageReserved set, so they will not trigger a false positive.
The check no longer blocks the mapping and uses err_printk() to
integrate with dma-debug filtering. |
| A use-after-free vulnerability in the Linux kernel's net/sched: cls_u32 component can be exploited to achieve local privilege escalation.
If tcf_change_indev() fails, u32_set_parms() will immediately return an error after incrementing or decrementing the reference counter in tcf_bind_filter(). If an attacker can control the reference counter and set it to zero, they can cause the reference to be freed, leading to a use-after-free vulnerability.
We recommend upgrading past commit 04c55383fa5689357bcdd2c8036725a55ed632bc. |
| Use After Free vulnerability in Linux kernel traffic control index filter (tcindex) allows Privilege Escalation. The imperfect hash area can be updated while packets are traversing, which will cause a use-after-free when 'tcf_exts_exec()' is called with the destroyed tcf_ext. A local attacker user can use this vulnerability to elevate its privileges to root.
This issue affects Linux Kernel: from 4.14 before git commit ee059170b1f7e94e55fa6cadee544e176a6e59c2. |
